Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. newBPhoneGuy

    Flare software

    yeah i know that you can also ghost them then change the wwid but i want the software i can actually install but it doesnt look like thats going to happen. thanks for the info
  2. newBPhoneGuy

    Flare software

    Hello everyone, Is there any way o get a flare recovery file and a flare install file, not the upgrade. i want to take 5 disks and install the flare from scratch how is this possible? Thanks for the help
  3. newBPhoneGuy

    Poweredge 1500sc

    replace the fan with a 1500sc they probable wont be that expensive and they are very easy to repalce
  4. newBPhoneGuy

    perc bios level

    POST
  5. newBPhoneGuy

    raid 5 issues

    the slot seems to be bad i would try to put a disk in another slot configure the driev as a hot spare and see it is rebuilds
  6. newBPhoneGuy

    Partner ACS R7 Voice mail card

    do you know how to tell which version i have
  7. newBPhoneGuy

    Partner ACS R7 Voice mail card

    hello, I have a partner acs R7 system with one on those little plug in voice messaging card and i was wondering how many mail boxes i can setup on it.....i would like to do about 8 if that is possible do you know about how many messages each box will be able to hold thanks for the help
  8. newBPhoneGuy

    PE4350 PERC2 and PV200s

    ok so i have a powerdge 4350 with a perc2 card connected to a powervault 200s.........we have it set one so it uses only one eem on the pv200 , about 6 months ago we started getting these errors stating the temp probe 0 was dropping below the minimum threshold which is like 0deg cel which is...
  9. newBPhoneGuy

    Voice Messaging PC Card

    oh and i only want the voice mail to pick up if i transfer the call to the extention and they dont answer in 4 rings
  10. newBPhoneGuy

    Voice Messaging PC Card

    Hello, I have the PARTNER ACS R7 and i want to add in the voice messaging pc card so that i can setup voice mail on one of the extentions.....can someone please help me and tell me the steps i need to follow inorder to get this to work??? Thanks
  11. newBPhoneGuy

    riloe with the dl360 g1

    yeah i know all that thanks for the help though..... I think it might have some hing to do with the firmware chip our vendor sent me 3 ore boards and they all work fine of couse i did make them test them on the same system i am using so......other than the firmware chip i cannot think of...
  12. newBPhoneGuy

    riloe with the dl360 g1

    yeah everythingis connected Im thinking maybe its possible that it is an imbedded firmware issue or something nbut i cant figure this one out.....
  13. newBPhoneGuy

    riloe with the dl360 g1

    hello im trying to install a remote insight lights-out board in my dl360. i have tried two different boards and on bothe of them i cant get the keyboard to work. I have tried it with all cables pluged into the board and all cables pluged into the system and no keyboard either way. the mouse...
  14. newBPhoneGuy

    Compaq Fibre Channel SAN switch HELLLL....P

    oh hahaha sorry i thought you said "make a model"...... all it says is Fibre Channel SAN Switch/8 with Fabric Operating Software 158222-B21 sorry about that thanks
  15. newBPhoneGuy

    Compaq Fibre Channel SAN switch HELLLL....P

    what do you mean
  16. newBPhoneGuy

    8 port fibre channel SAN switch

    i have an 8 port fibre channel SAN switch by compaq. when i connect a serial cable and power the thing up it takes me to the prompt <VxBoot> or something like that. and when i try to boot with the @ command it fails and says i need to enter a valid ethernet address everything i try to enter...
  17. newBPhoneGuy

    Compaq Fibre Channel SAN switch HELLLL....P

    ok i got the serial port to work now i think i need to boot the switch but im not sure when i do a @ to boot it says the ethernet address is invalid
  18. newBPhoneGuy

    Compaq Fibre Channel SAN switch HELLLL....P

    hello everyone im have a bit of an issue with this 8 port fibre channel san switch. I connect a network cable between the switch and a dl360 and connot telnet to the default address...It is possible that someone has changed the address and did not write it down.....so i try to connect a serial...
  19. newBPhoneGuy

    partner messaging r2

    ok i want to set up a couple mailboxes on my system so i need some info is all i need to do is to do the initial programming on the messaging pc card then assign ext 78 and 79 to hunt group 7 then program automatic for the ext.'s i want to have voice mail correct? all i want it to do is go to...

Part and Inventory Search

Back
Top