Search results for query: *

Thank you again everyone for your assistance in this matter. Added the VLAN statements under VTP transparent mode and it work.

anks everyone for assisting me in this matter. Will find out today or tomorrow if it going to work

Here are the results of the VTP Status from the switch. Hope this helps Switch#sh vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 68 Number of existing VLANs : 5 VTP Operating Mode : Server VTP Domain...

Yes i am

TY for you response silverblade, I am not sure if its setup for a VTP client. I was trying to configure to see if that was it, but the switch does not like the commands I enter. Here is another part of the config that might help. The config on the ASA has a vlan 3 Thank You, vlan 3 name...

Apologizes for being vague that what happens when its 5:00 HAHA. Below is the statement added to one of are switches. I am configuring a new switch and I can’t get this statement added. I know I am going to need it in order to get the guest WAP up and running. I hope this helps. If you need...

Apologizes for be vague that what happens when its 5:00 HAHA. Below is the statement added to one of are switches. I am configuring a new switch and I can’t get this statement added. I know I am going to need it in order to get the guest WAP up and running. I hope this helps. If you need...

This is for a guest network in our company. Was wondering on how to add a vlan 3 statement. It is not a interface for Vlan 3 it is just a statemwnt for it. Does any no of the commands to enter this into a 2960 switch? Thank you

Thamk you for your reply Jml2665. I will try that.

Thank you for the reply. I don't want to have that specific number ring on one of the phone line appearance. I want it so the pots phone number it self rings on that 1 phone and that all. Same thing with the all the other pots phone numbers to ring on individual phones. One phone number points...

Was wondering if there was a way to have a point to point set up in an IPO. I want to have POTS line coming in to the analog trunk and have a specific extension and only that extension ring from that number. Just wonder if it’s possible and if it is what has to be configured to accomplish this task

How do you view a UDP plan that was created so i can enter extensions in it?

Thank for the responses. Was wondering where do you enter the extensions in the UDP plan. This is a setup for a S8700 to communicate with a IPO over a VCM card in the IPO.

Was wondering what is the command for accsessing the UDP plan in a s8700?

I was wondering if there is a way to access the VM from the outside the building? Sort of like you can with intuity audix

Does a Main hunt group number have to be a DID? What if a number that has already been setup in your rebase extension list and you want to use one of those extensions as a main hunt group number can that be done?

Thank you for the reply, But I need to have the extension inside my DID range for the pots 1 and 2 and have a specific extension off of the DID range. These are for fax machines. Basically what is happening is we have an IPO 406, 2 digital modules 16 port each and an analog module 8 port. The...

How to assign pots 1 and 2 to a specific extension rather then the first two extension on the rebase? Reason for the question is we have more ports then DID's that we purchased.

I’m trying to have my s8700 communicate with an IPO 406 through a VCM card in the IPO. When reading the documentation it is saying that we have to set up a 5 digit extension on both sides. We are currently using 4 digit extensions at all my locations. Does it have to be a 5 digit or can it be a...

How do you configure a H.323 Trunk in a S8700 media server so it can communicate with an IP Office 406 with a voice compression module?