Search results for query: *

but what if your system root is on the d:\ drive?

In doing a DR restore, we have a support partition on our servers (C:\) and a system or production partition (D:\) we start the support partition (or create a new one) and run the client to restore the prod (d:\) partition from backup, but when we select the System state restore, it always...

Ive tried this too -- even tho you can share calanders and view them on you client -- you can only active sync one calander, your primary.

ptiernan - im having the exact same issue and the KB article didnt help much either. do you have info on that fix you did to remove the errors handy? Thanks!

hehe..a little late, but here are the two direct links for v7 sp2 and v7 sp2 update update: http://h18000.www1.hp.com/products/servers/management/sp23545.exe full: http://h18000.www1.hp.com/products/servers/management/sp24904.exe

I use: 1-866-MY-ANI-IS (692-6447)

Perfect -- that is exactly what i needed. thank you very much. -Bill

Where can i find info or documents on this 909A/B Universal coupler, i have 2 and have no idea what they do.

if this is in an analog port, doesn't it need a 600ohm resistor??? if its in a AUX port, a resistor is not needed -BillyZ

anyone seen or use these still? what exactly is thier purpose? I have 2, one on my MOH, and on my Paging. anyone know the pin outs? they both connect to a 66 block with a mess of wires and jumpers and that is not my style, i want to clean it up a bit. Thanks - BillyZ

Dont forget the 600ohm resistor ... you could damage your equipment. -Bill

I know its been a while, but i wanted to close this out -- To fix the problem, I re-flashed the PIX (actually there was an update available, so now it works OK, all can ping all) -BIllyZ

6.1(1) I looked and didn't see anything in the 'whats new' could've been a corrupted image too i guess.

I fixed the problem by upgrading the flash to 6.2(1) weird.

I remember recently reading that too...suprising. hmmm....OK, i have a spare 2501, i'll try it out. Thx. -Bill

I posted this on the Cisco PIX forum...hopeing to find some help here. thread35-289304 a weird one. I have a switched network with about 125 clients. All connect to 9 3com 3300 switches. I use a PIX 515 for internet access and reporting. One fine day, several workstations stop working...

I'll post this in the 3com forum also. 3 floors, each floor has 3 switches. Each of the group of switches are connected together using the 3com module. So each floor has a separate group. I am not really in agreement with how this is setup, i Inherited this network, and am planning on...

Hey Yizhar -- im a big fan !!! i read all your posts. ok, enough sucking up. :) here are the answers to your questions -- you may have something with the config of the switches... Now - are there any special configuration at the SWITCHes? All switches are set to default...now we have 3...

heres a weird one. I have a switched network with about 125 clients. All connect to 9 3com 3300 switches. I use a PIX 515 for internet access and reporting. One fine day, several workstations stop working (unable to access internet), they are unable to ping the default gatewway (which is the...

What I really hate is this: configuring an IP address for my card, my network is 192.168.0.0/22. If i set the ip address to anything 192.168.*.*, it forces me to use the subnet mask 255.255.255.0 (not 255.255.252.0, which is what I set up the network to be) Now, if i give it a 10.*.*.*...