Search results for query: *

I'm trying to set up a tunnel between a PIX 515e and 7206. I get the following errors from my debug crypto isakmp: ISAKMP: reserved not zero on payload 11! error - payload malformed I know what this error references on payload 5 but I can't find any info on payload 11. Anyone familiar with...

You rock Chris! That worked. Thanks so much!

We recently migrated to a new Exchange server. I changed the static statement on our PIX 515E for the existing public IP address to the private static IP address of the new server. But emails are still being routed to the old server. When I telnet to the public IP on port 25, it displays the...

Thank very much for the input!

In Exchange 2000, I need to prevent the entire domain from sending to 20 specific outside email addresses. The "Delivery Restrictions" tab on the SMTP connector seems to only block all external emails from users/groups. Any help is much appreciated. Thanks

Thanks for your help. It is much appreciated!!!! Mike.

I recently installed a second connection to my ISP on a separate subnet. I put two 2621's using GLBP outside our PIX 515e. So the default route on the PIX points to the GLBP ip address. The load-balancing method is round-robin but every host goes out the same router. I believe this is due to the...

We have a switch stack of Catalyst 3750's. 3 of the ports were err-disabled. I did a show interface status err-disabled. Here is the output: Port Name Status Reason Fa2/0/41 err-disabled loopback Fa3/0/33 err-disabled loopback...

Hi Dave, We also have a 3rd party that we relay to. I setup a new SMTP connector in our routing group. System Manager->Administrative Groups->Routing Groups->your routing group name->Connectors; Right click connectors and create a new SMTP Connector. Click "Forward all mail through this...

I have an Exchange 2000 OWA server that I recently ran the IISLockdown tool w/ URLSCAN. Now when you click on the 'change password' icon, it brings up the 404 page, "page cannot be found". I removed the deny .htr line from the URLSCAN.ini but that didn't fix it. Any help on this issue is much...

I ran into some problems adding a catalyst 3750 switch to an existing switch stack. I set the priority on the Master switch so it would stay the master after the re-election. I powered down the switches, recabled the stack ports, and powered them back up. The POST was successful so I logged in...

I'm trying to write a script that will sweep through and delete files older than 3 months. The script works fine on the folder I specify but I need to sweep through all of the subfolders as well. Any help is much appreciated. Here is the script: Option Explicit on error resume next Dim oFSO...

Thanks lander215! I did a second search for 'disclaimer' instead of 'confidentiality' and there were quite a few posts. I ended up going with the eXclaimer product. It has worked well so far. Thanks again.

I need help adding a corporate Confidentiality statement to all outbound emails. Our email servers are running Exchange 2000. Any links or suggestions is much appreciated. Thanks.

Did you add the 'backup' site subnet to Subnets in AD Sites & Services? Then, create a new Site for the backup subnet. Hope that helps!

I would check two things: 1. Make sure the Computer Browser sevice is started on the Server not showing up. 2. Check the Advanced TCP/IP setting on the NIC to make sure NetBIOS IS enabled. Hope this helps!

Tuka, I booted to cdrom, mounted the root slice, and found out the /etc/hosts file was empty. The hostname.eri0 was set correctly. So I added the correct entries in the hosts file. The server booted correctly. I'm still not sure how the hosts file got corrupt since this server has been in...

On reboot, one of Solaris 8 servers hangs after "hostname": bad value. Also, I see the following: configuring IPv4 interfaces: ifconfig: "hostname": bad address eri0 No changes have been made to /etc/hosts or /etc/hostname.eri0 Any help would be much appreciated. Thanks

How do I specify the domain name in the return-path in Sendmail? It defaults to user@hostname.domain. I set DM to the domain I want but the return-path in the header still references the user@hostname.domain. Thanks in advance

On a SCO Unixware box, scripts are overwritting logfiles instead of appending to them. Even if I do: echo `date` > test echo foo >> test test only contains foo. I appreciate any help/insight anyone can provide.