Search results for query: *

Hi all, Is it possible to configure a router to be an access point for VPN authentication to a specific Radius server, and also remote management via ssh to a different server? If so, how would that be done?

Found the problem... The carrier we use uses a Alcatel switch and both switch ports are setup exactly like that... switchports... We, on the other hand, have the Lan Extension ports on both switch configured as trunk ports.... See the problem? So to test this, I setup for ports on the...

Hi all, My setup is : SW3 Cisco 6509 Switch -> Vlan Trunk -> SW1 Cisco 6513 -> Etherchannel Vlan Trunk -> SW2 Cisco 6513 -> firewall (fortigate) -> internet... The PC can ping from SW3 across to the internet without any issues. Although, when trying to surf the internet, it times out. The...

Hi all, Newbie... trying to setup a ssh perl script to login to a device and execute a command. 1) The device has 2 levels of password, meaning when you login with : my $ssh = Net::SSH::Perl->new($server); $ssh->login($username, $password); the system ask's for a second password that...

Now that the Vlan's all have IP address, How do I route between them? My SW1 does not want to take the IP ROUTING command, yet SW2 will. Both are running identical Hardware and Software. Someone somehow diaabled IP ROUTING on the SW1 and I cant find anywhere in the docs how to start it back up...

then how do I setup routing between vlans? I can't seem to assign IP's on the vlans, it wont let me. Is this system runnign in Hybrid mode?

Hi all, For Inter-Vlan Routing features on this switch, what is the feature set required? As the 12.2(18)SXF does not have IP Routing...?!?

I did reset and it came back normaly, no syslog... DOUGH! but was trying to figure out if tehre was a way to find out from within, what happened.

Hi all, How do you find out what happened prior to a cisco 3600 rebooting into ROMmon?

thanks for the quick reply, ill try that

How can I do this? Im using Flash MX 2004 and make a flash of 468x60 then I add a text then I add (on a different layer above the text) as transparent box. for the keyframe of that box I enter the actionscript: on(release){ getURL("http://www.google.com", "_blank"); } Yet, the swf when...

Hi all, Question: How do you setup round-robin on a Cisco 3640. I have 1 ext IP that I want to round robin to 2 internal IP's on inbound traffic. Thanks

I just tried using PBR as documented and that also is not working. ! interface FastEthernet0/0 ip address xxx.xxx.xxx.253 255.255.255.0 ip nat outside ip virtual-reassembly no ip route-cache ip policy route-map SIP speed 100 full-duplex no mop enabled ! interface FastEthernet1/0 ip...

What information do you need? It's basicaly all traffic hitting 66.46.196.120 on port 80 and 5060 should be sent to 10.1.10.10 inside.

I tried, I can t get it to work... What I need to have a specific Public IP going to a Specific Private IP. I tried using Static 1-to-1 NAT but it's not working.

How could I do this? What I was inquiring about is how to setup the Cisco 3640 to route traffic comming from one specific Public IP ( the wan interface has 2 Public IP) to route it to a Specific LAN interface. So for visuals : Public IP 66.46.196.120 \...

You TP10x is a SIP host card right? I'm pretty sure you have 2 eth ports on that correct? (I use the Mediant2000 and it has 2 ETH ports as Active/standby). Make sure your connected to the active port.

Hi all, Trying to figure out how to lock down SNMP from the external interface of a 3640 to a public IP address. ex: Cisco 3640 206.22.33.44, only allowed to/from 206.22.33.55 What should I use? Extended ACL or standard ACL? !snmp server for PRTG bandwidth monitor. snmp-server community...

That's what I figure because theres no talk about ethernet, only Fast Ethernet on all configuration documentation of Cisco's. Thanks for the info! NP

So is the image name c2600-js-mz ? If so, then I would need a 64MB Ram and 16MB Flash right? Regards, NP