Search results for query: *

I have 3 xbox's that I need to forward multiple ports. I have found multiple examples how to port forward one port to one host, Is it possible to forward ports to multiple hosts? I need these ports forward to hosts 172.31.1.50, 172.31.1.51 and 172.31.1.52 Port 88 (UDP) Port 3074 (UDP and TCP)...

There is no frame relay lab on the ccna

My first thought is why do you have two static routes pointing to the same network on switch one. ip route 192.168.6.0 255.255.255.0 192.168.203.10 ip route 192.168.6.0 255.255.255.0 172.18.32.16 and another two static routes for switch 2 ip route 192.168.6.0 255.255.255.0 172.18.33.250 ip...

Remember to adjust the the timers for hsrp to make it scream, We use msec rather than seconds.

Make sure you also specify your username username admin privilege 15 password imin

I would use vlan access maps

How do I enable Radius authentication on a 6500? Here is what I use for a 2970 but the 6500 doesn't have the radius-server command. radius-server host 10.12.1.10 auth-port 1645 acct-port 1646 key 7 ********* radius-server source-ports 1645-1646 aaa new-model aaa authentication login default...

Posted by: elovelace256 Oct 31, 2007, 11:57am PST I have a 501 at a branch office that I need to port forward www, ftp and rdp to 3 diffrent hosts. The outside interface is dhcp and the inside is 10.50.1.3 the network is 10.50.1.0/24 Below is what I thought would work but it is not...

Is there a way that I can monitor if a vpn tunnel is up or down? I know you can do sh cry isakmp sa or via the asdm but that does not alert me if a tunnel is up or down, or give me any historical data about the tunnel. I tried via solarwinds but it only lets me monitor the interfaces and not...

Can someone see why I can ping from vlan 25 to vlan 5 and vlan 5 to vlan 55 and vlan... ect ect. I can't figure this out and would appreciate quick help. Thanks in advance! Current configuration : 4430 bytes ! version 12.1 no service pad service timestamps debug uptime service timestamps log...

Try this route inside 172.16.5.0 255.255.255.0 172.16.5.1 1 This will only route the 172.16.5.x network traffic or change your default route to route inside 0 0 172.16.5.1 1 of course I am assuming the router for the point to point is on the inside network.

you are right, I was thinking of how the pix works, I am going to have to nat the 192 subnet. Actually I already did and it works for me. Just for refernce here is what I added access-list 1 permit 192.168.1.0 0.0.0.255 ip nat inside source list 1 interface GigabitEthernet0/1 overload ip nat...

Yes I absolutly understand pat and nat, What I am saying is I cannot ping the next hop off the outside interface from a host on the inside interface which that may involve pat. But when I perform an extened ping from the outside interface(see below for example) I do not get a reply. i think...

Sure no problem, Here is why I don't think I would need to nat that address. If I have host a on the internet trying to get to host b with the ip address of 192.168.1.5 then I would have to static nat a public ip to the ip of host b. But that is not what I am doing I am simply trouble shooting...

No go, Didn't work, Since I removed the next hop and replaced it with the interface like you said. I added the ip default-gateway.

Thanks for the reply, I understand nat and that is not what I need. When I say I am pinging the inside network 192.168.x from the outside interface I am talking about doing an extended ping. I am actually performing the ping on the router and not on the internet to the non routable 192.168.1.x...

I have a 2800 series router that I have specified the ip's for both interfaces, enabled routing, put the default route in and made sure the interfaces are up. I can ping from the outside interface to the next hop and get a reply. But if I ping from the inside interface or a host on the inside...

I have two 2801 routers. One of the routers has a t1 wic. The outside t1 wic has an ip of 10.1.1.1 and the inside has and ip of 10.1.1.2 The second router is a vpn connection that will be used for redundency. The inside ip is 192.168.1.1 and the outside ip is 10.50.1.1 How can I set these up...

I was send this configuration and I cannot get this command to work. Can someone please help? interface Serial0/0/0:0.575 point-to-point I get this error % Invalid input detected at '^' marker. and the marker is at the 0 after the : This is on a 2800 seriers router Thanks in advanced

I have a pix 501 and have been banging my head against the wall. I need to open ports • UDP 88 • UDP 3074 • TCP 3074 for xbox live. My outside interface is dhcp and my xbox ip is 10.6.1.12 How do I nat 10.6.1.12 and create and access list for those ports? Much help is appreciated