Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. shinydonut

    Warm reboot function not implemented?

    Hello, I recently upgraded the IOS on our Cisco 7206 VXR router to 12.3(11)T because of the warm-reboot and new warm-upgrade functions that I read about. Well, after upgrading, I enter global config and type ? only to find that the warm-reboot command doesn't exist. Have I been duped into...
  2. shinydonut

    policy map question

    I've tried using the police command, but it doesn't seem to limit the speed at all for P2P applications. The command I used is as follows: Router(config-pmap-c)# police 8000 1000 conform-action transmit exceed-action drop The traffic across the interface was still around 3-4Mbps, since the...
  3. shinydonut

    policy map question

    Thanks for the reply! So basically, if I'm using the policy-map command, my only options to limit traffic on the input traffic are by using the drop or police commands?
  4. shinydonut

    policy map question

    I am trying to configure a policy map for the input traffic of our 7200 router running IOS 12.3.8T4. The commands I'm using are as follows: Router(config)# policy-map limit-traffic Router(config-pmap)# class slow-down Router(config-pmap-c)# bandwidth percent 10 Then I try to apply the policy...
  5. shinydonut

    slow contact searches in Outlook 2000

    Hi, I have a client using Outlook 2000 SP3 with a contact list with 4700 contacts. Performing a contact search takes a long time; 45 seconds or longer. Is this normal? If not is there a resolution to this problem? Any ideas would be appreciated.
  6. shinydonut

    Cisco 2620 and NAT

    I just performed some nslookups using your DNS server's outside IP and everything works fine. If you're on the inside, it's not possible to use the outside IP to do nslookups. That's just the way NAT works. Rule of thumb is any computers on the inside should use the 192.168.10.2 and .3 IPs...
  7. shinydonut

    any load-balancing multi-homed solutions?

    Hello, Recently, we added 3 ADSL lines to our office to use as our backup WAN, and I was wondering if anyone knew of a solution where I could load-balance the traffic evenly between the three ADSL modems? I'm using a Catalyst 6509 switch with 3 VLANS. Each VLAN uses a single ADSL modem as the...
  8. shinydonut

    any motherboard troubleshooting software?

    hi all, i have reason to believe that one of the RAM slots is failing on my motherboard. before i take it to the shop though, i'd like to see if there were any utilities out there that i could use to see if this is truly the case. any help will be much appreciated! thanks! rich
  9. shinydonut

    how to convert .msg to .pst?

    Hi, My company has decided to migrate our email from MDaemon Pro to Exchange 2003. MDaemon stores each email as a separate .msg file and we need to convert it into a format which Exchange can read. Does anyone know how? Thanks in advance for any help! Rich
  10. shinydonut

    can't log in

    When I try to telnet into my Solaris 2.7 server, after I type my username, I get an error that says "too many files open". I go into /etc/system and change the rlim_fd_max and rlim_fd_cur to 4096 and 1024, respectively, and reboot the server. When I try to log in again, after typing...
  11. shinydonut

    weird error at login prompt

    Hi all, When I try to telnet into my Sun Netra T1, I get the following error: ld.so.1: login: fatal: /dev/zero: open failed: Too many open files I checked the Sun docs, and they say that I need to increase the number of file descriptors, so I enter single user mode, do the ulimit -n 256, then...
  12. shinydonut

    using MRTG with Cat 6509

    Hi, I am trying to graph the CPU utilization of my Cat 6509 using MRTG. Unfortunately, MRTG complains about some error with the OID. I've checked and double checked this number at Cisco's website, and there shouldn't be a problem. I can easily monitor the CPU on the layer 3 level, but I...
  13. shinydonut

    cron job won't run!

    Hi, I'm trying to run a cron job that will change the ownership of a file in my home directory. But for some reason, the job won't run! Here's what the line looks like: 5 0,12 * * * /usr/bin/chown nobody /export/home/user/example.txt That's all on one line. When I check the /var/cron/log...
  14. shinydonut

    CDE won't start at boot-up

    I just reinstalled Solaris 2.6 on my E450, and when it boots up, the CDE doesn't start. Instead, it gives me a prompt to log into a command line. The S99dtlogin file is in /etc/rc2.d, so everything should be ok. Using Exceed from my laptop, I am able to open the CDE, but not from the...
  15. shinydonut

    adding secondary IP address on startup

    Hi all, I was wondering if anyone has written an rc script which adds a secondary IP address to the hme0 interface upon startup. Currently, every time I reboot my server, it comes back without the secondary IP address, and I have to manually add it back in. I have zero knowledge of how to...
  16. shinydonut

    configuring MRTG to monitor switch ports

    Hi, Has anyone used MRTG to monitor the ports on a Cisco switch? I have a 3500 series switch, and I have no clue how to set up the configuration file. I've set up MRTG for my Cisco routers without a hitch, but the ports are giving me some problems. Can anyone help? Thanks! Rich
  17. shinydonut

    provide internet access

    Perhaps you have mismatched encapsulation on the Serial2/4:0 and Serial0 interfaces. I had the same problem before where I could ping and traceroute between the two networks just fine, but when I tried to access the internet, it wouldn't work.
  18. shinydonut

    increasing minimum password checking length

    By default, Solaris only checks the first 8 characters of a password field. I was wondering how I could configure it such that it will check more than just the first 8. Also, after I've changed the configuration, what do I have to do for the change to take effect? Thanks!
  19. shinydonut

    Can't ping static NAT translation IP address

    I am doing NAT on my 7206 router, and I am mapping several internal IP addresses to global IP addresses. What I am seeing is that if I try to ping the globally mapped IP address from inside my network, I get a 50% success rate, ie it drops every other packet. Is this normal behavior or am I...
  20. shinydonut

    Redirecting HTTP requests to Cache server

    In order to redirect port 80 requests, you must use WCCP (Web Cache Control Protocol). Most cache servers support this Cisco proprietary protocol. To enable on your router, use the following commands: router#ip wccp version 1 router#ip wccp web-cache router#conf t router(config)#int (whatever...

Part and Inventory Search

Back
Top