Search results for query: *

I think the LEC is asking "how many outpulse digits", as in how many digits do you want to receive on calls to your PBX for DID service. Normally this would be the same number as your station dial plan. That way you don't have to make modifications to the incoming digit string, it's just the...

Dear Telefolks, How can the 87XX or Definity Switch be configured such that the ISDN SETUP message going out a PRI will contain the "Redirecting Number Parameter" and "Redirecting Number" information element, allowing the call to be correctly billed by the LEC, if it was forwarded by a Definity...

GREAT question! I was hoping that in a call forward situation that the switch would route the call based on the COR of the station doing the forwarding, but it does not seem to work that way.

Does Avaya support "offnet" voicemail? Thanks!

Thanks for answering, but how would this be configured to send RN for Offnet Voicemail? Sorry, I don't see the connection between 911 CAMA and RN for Voicmail. Thanks.

Dear Telefolks, How can the 87XX or Definity Switch be configured for off-net voicemail, such that the coverage call ISDN SETUP message going out a PRI will contain the "Redirecting Number Parameter" and "Redirecting Number" information element, allowing the call to get to the correct mailbox...

4630 Phone was working. Now phone still works to make calls, but touchscreen application does not start. Screen shows only text with time and date, and a= when off hook. When booting, the phone used to show a colored graphic screen with welcome to the 4630 screenphone, now it is just plain...

Could you share it? =-)

Thank you, I found a translations flash card which just happened to have the WFB and radio controller firmware, but it had only newer phone firmware. I was able to upgrade the WFB and radio controller just fine. I guess I'll just have to keep collecting old translations flash cards until I...

Does trunk group page 2 of your R6 switch have a field like this: US NI Delayed Calling Name Update? n For National ISDN CNAM to work this usually needs to be set to Y. This is because the LEC sends your call setup message right away when you have an incoming call, while the LEC switch is...

Please help if you can. It would be too bad to have these old phones in the PBX museum in non-working condition. Thanks.

I'm looking for firmware for Definity Wireless Business System 9601 phones that would have been stored on a 10MB or greater translations flash card. "Status Card-Mem" will show if a card has DWBS firmware = Y. This is then viewable on a card that has it with "list config firmware". I need...

Since your TG 2 LD group is not ISDN, the only calling party number that can be sent along in the AT&T network is either nothing, or one filed on the TG in the AT&T Switch. Do your calls come up "unknown" on the far end?

Once your outbound call enters the public network, the name associated with a given calling number must come from a database in the public network, whether it is the local CO Switch (Canada), or the carriers' AIN database (USA, theirs or their CNAM providers). I suspect your main number is not...

Can a Definity R9.5 accept incoming MF signalling with ANI, as in Feature Group C CAMA? I know the Switch can outpulse FGC CAMA, but I suspect it cannot accept it incoming. Incoming DTMF *ANI*DNIS* works fine, but we have an application for MF with ANI. Thanks.

Where is your service area? I find it hard to believe any regulatory commission would impose 1+ dialing for local calls. Are you sure there is not some confusion here? Good luck!

Merlin Forum? =-)

As long as the DS1 port settings are the same on your DS1-DS3 mux as those parameters used on your copper DS1s you should be good to go. Framing (SF or ESF), line coding (AMI or B8ZS), and then the correct line build out (wire distance to your PBX )must be set on the MUX.

Did this command always work like this, or did it change at some release? Thanks!

Thank you very much!