Search results for query: *

I have this same problem! (nice to know i'm in good company). User can't ever logon in the morning, i go and login as admin, and log off and then she can login just fine. I checked the security event log and i get a ton of Event ID 529 (Failure Audit) and Event ID 538 (Failure Audit). Any fix...

I've got a Linksys SPA8000 VOIP gateway that i'm setting up to connect to my PBX. I've been strugging with Nat Policies, Access Rules, and the VOIP tab (enabling Sip Transformations, and Constant NAT). My VOIP gateway is sending packets just fine, but receiving 0 packets. Last night i took the...

I've recently setup vlans on my network, 1 vlan (vlan 0) is my HQ office with a Pro2040 and the other 2 vlans (Vlan 1) and (Vlan 2) are just in my Branch office connected by P2P fiber. Vlan 1 carries all data traffic while Vlan 2 is just for VOIP. Since i've converted my network to Vlans from...

I don't think it's worth it as I have a 2040 on Enhanced 4.0 and don't find this Layer 7 QoS to be what i am looking for as it's not pro active enough. The shaper will not only QoS layer 7 but also (as you said) compress and accelerate) as well as provide extenseive reporting on what users are...

Thank you for the reply, i did that via ALI, just didn't see it show up in the web interface under Vlan Priority. One thing i did do was set the wrong vlan to voice, any idea how to "un voice" a vlan. I tried vlan 1 voice, to see it it would toggle it back, also vlan 1 no voice, and a few...

I'm trying to setup QoS to have anything on Vlan 3 be set to Highest Priority (7). This is for a branch office that will have VOIP over a Fiber P2P link, as well as their internet data so PCs will be on Vlan 2 and Voip Phones will be on Vlan 3. I see a tab in the QoS configuration menu showing...

I've got a similar problem, I have a 2Mb fiber link between my HQ and branch offices that was just put in (cut-over from a Point to Point T1 that used routers). Since this Bo doesn't have a router I set them up on a seperate Vlan but i see about 150k of traffic going across that line even over...

Thanks for the response. Do you have your Sonicwall do all of your routing or do you have this in place betwen a router and your WAN? I can either get 1 Layer 3 switch, and 2 Layer 2 switches, or just get 3 Layer 2 Switches and keep the sonicwall inplace as the router. Thanks!

I've got a Site 2 Site VPN, and it keeps dropping. I setup PRTG Traffic Grapher (great program) and see that the the VPN is dropping when bandwidth is maxed out. Is there a way to prioritize the Site2Site VPN so this doesn't happen? Thanks!

I've got a Pro2040 in my HQ and a TZ170 in my Branch office, I haev 1 VOIP phone in this office that connects back to the PBX in the HQ via this VPN. The VPN goes through phases of bouncing a few times per day, which prompts me to go in and change the settings for the VPN, say from Main to...

I've got a 75 user network i support, and i'm looking to upgrade my older 3com layer2 switches to something newer. I also would like to take advantage of Vlans. Currently my Sonicwall is doing all of my routing, i'm wondering if a layer 3 switch might do better and have the sonicwall just...

Anyone know when the Enhanced 4.0 firmware will be out?

If you don't see the X2 interface in your Failover / LB screen then that is the problem. Looking at my setup (Pro 2040 with two ISPs and two IP Blocks) I see my X1 and X2 are both configured as WAN zone. In my failover / LB tab i see them both there. Maybe try to delete the X2 Wan Zone and...

Ooooooo.... i will definately check that out. Thanks!

Well bandwidth management doesn't give you the granularity a shaper would, as it isn't an application layer (layer 7) device. You can only block or limit bandwidth on ports rather then the applications themselves. I appreciate the reply though and thank you for the suggestion as it may work for...

I too am looking for some help with Vlans. I've got a branch office that is connected via MPLS VPN so there is a router on my HQ and a Router in the BO which creates a subnet for that office. My Core Router is simply directing all traffic for that BO subnet to the VPN router. I will be...

I've been reading a lot of articles and whitepapers on packetshaping and WAn bandwidth management, some of which made me wonder how applicable this may be in a 70 user environment. I'd mainly like this technology to be able to prioritize my business applications, as our main system is a hosted...

How is there mailserver input in the profile setup, by server name or by IP address? I'm wondering if it's an issue with the VPN not sending broadcast traffic so the name is not resolving. Try the Ip and see what happens.

The issue between the DSL and the Fract T1 speed difference is because the DSL isn't guarenteed speed but rather Best Effort. The Fract T1 is guarenteed and instant. I switched 1 office off a Fract T1 (384k) to a 6MB down 2MB Up cable modem as it was only 1 person. This works fine for VOIP and...

I'm looking into redundancy for a VPN connection that connects my HQ office with a branch office. My current setup is a PRO2040 in the HQ and i use routing roles to send all traffic for the Branch Office's subnet to a Cisco Router, which is connected to a Point to Point (P2P) T1. I'm looking...