Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. wagtech

    IPECS eMG80 Rotary Phone and Pulse Dialing

    Is there ports for SLT's installed, if so then Program 110 Station Type should allow you to pick from the following... In case of selecting SLT type, there are 6 types as below:  SLT (DTMF)  SLT (Pulse)  SLT (DTMF VOL-MW)  SLT (Pulse-MW)  SLT (DTMF FSK-MW)  SLT (DTMF POL-MW)
  2. wagtech

    IPECS eMG80 Rotary Phone and Pulse Dialing

    Very helpful, by your use of 'probably' probably means you don't know. eMG80/800 DO pulse dialing as long as the appropriate boards are included. Suggest if YOU don't know then don't comment.
  3. wagtech

    UCP600 Emergency Calls

    Thanks for the info, greatly appreciated.
  4. wagtech

    UCP600 Emergency Calls

    Would the leading digit table cause issue with the outgoing CO digit 0 if the system also looks for 000? Daniel_RO if you try this would be good to know how you go.
  5. wagtech

    UCP600 Emergency Calls

    International Subscriber Dialing, Australia has 0011 or 0014 for international outgoing calls followed by country code + area code + phone number (not that anyone would pay to use it if they use chat programs now days!).
  6. wagtech

    UCP600 Emergency Calls

    I see a problem with that in dialing 0 then 00 with an 0 added by the system you then bar access to ISD (001x). As soon as you dial 0 then 00 the pbx will add 0 unless you specifically assign another digit/s for ISD or not allow ISD.
  7. wagtech

    Setting up SOE using SIP to Asterisk system

    If you try this link and then I can email you the config details direct- http://www.nontaurus.com/msgs/ToAdmin.asp If you are party to this... Phil
  8. wagtech

    Setting up SOE using SIP to Asterisk system

    1) Only one (trial at present, just ordered two licenses) 2) Extn setup is basic as below- Ext cfg exten => 201,1,Macro(exten-vm,novm,201) exten => 201,hint,SIP/201 Sip cfg [201] username=201 type=friend record_out=Adhoc record_in=Adhoc qualify=no port=5060 nat=yes mailbox=201@device...
  9. wagtech

    Setting up SOE using SIP to Asterisk system

    It looks like the ipo is failing on i/c calls starting with 8xxx. But aren't you stripping 8 in the *? Maybe try turning on SIP Tx and SIP Rx on Monitor to see what the two units are sending each other in the SIP packets. Post here if you want.
  10. wagtech

    Setting up SOE using SIP to Asterisk system

    Oh and I forgot to mention having an incoming call route on the IPO for each ext to map the * ext (or group) number to the IPO ext/group.
  11. wagtech

    Setting up SOE using SIP to Asterisk system

    Ah, so you DO have audio both ways on a call, my problem was one way audio on a call. On my setup I dont use registration on the * only set the ip address for the extension (the IPO's ip), in fact I have all the IPO's exts existing on the * with the same IP so you can dial any ext on the IPO...
  12. wagtech

    Setting up SOE using SIP to Asterisk system

    Ditto for the setup. My setup IPO with no NAT, * with NAT. IPO only calls the * or through it to outside world. To receive calls I have calls route via the * ext. to the IPO Are you able to make a call out with audio both ways from the * direct? Check on the * monitor how the call is...
  13. wagtech

    Setting up SOE using SIP to Asterisk system

    eholm, would have to do with turning on NAT on the asterisk side? What I just found was the asterisk side was sending its public IP to the SOE causing the SOE to reply back to the public address. Now that I have turned on NAT on the asterisk side it now sends only its LAN ip addy. It now works...
  14. wagtech

    Setting up SOE using SIP to Asterisk system

    After a bit more investigation voice is going out of the SOE but not in. So may not be a codec issue!?
  15. wagtech

    Setting up SOE using SIP to Asterisk system

    Having a problem with audio between SOE Sip trunk and Asterisk PBX where audio seems to be one way then after a while the call disconnects (most likely to quiet timeout). Sounds to me to be a Codec issue, does anyone know which codec is best on either side? Unless someone has other ideas... Phil
  16. wagtech

    v405 Problem with group announcement on SOE

    Dont think you read my email correctly, I have already done all that. Twice! Still not working.
  17. wagtech

    v405 Problem with group announcement on SOE

    I have recently upgraded my SOE system to v4 and tried to use the new announcemnts for groups. It plays MOH ok but when I try to record an announcement using the short codes as per the docs I get silence and monitor reports the call going to VM but no mailbox exists. Using Embedded VM which was...
  18. wagtech

    Upgrade of SOE to 4

    Hi, I have a IP Office - Small Office Edition 4T + 8A I would like to upgrade to v4 but after reading the docs it 'seems' this version only supports a max of 4 analogue ports. Will 4 break half my ports or does this refer to newer versions of the SOE? Wanting to upgrade to take advantage of...
  19. wagtech

    Caller ID not working for external calls

    No, I have even updated the firmware to 2.1 with no difference. As metioned earlier the system accepts the number ok but will not include the name listed for that number in the IPO directory. I still believe this maybe because the word MOBILE is sent from the telco and not being replaced with...
  20. wagtech

    Caller ID not working for external calls

    After a bit more investigation it seems to work fine for normal numbers but not for mobiles, I'm wondering if it has to do with the network sending the word MOBILE with the number as that is all that appears for the name. I have tried using single names and adding brackets as a area code...

Part and Inventory Search

Back
Top