Search results for query: *

Hi We have just replaced the filter kit but do not know how to reset the counter. Can anyone assist? Many thanks

I have an OKI B6100 with a strange fault. . . it comes up with fuser jam code E3 when printing from the Manual feed...... From the control panel on the printer I set the manual feed tray as default and the appropriate paper size/type. whether it be from the computer or the printer controls, I...

Hey all I have a Xerox 7760 in need on the black plastic interlock switch actuator which pushes the white arms to hit the interlock switch on the left door. It is on the left door assembly at the top rear. I cannot find this in the service manual and was hoping someone could let me know the...

I am investigating error 15 on a phaser 7700 but am unable to reset the error in tech mode as it wont let me enter tech mode. . . I have switched the printer off and then pressed and held both the back and info keys and powered on. . .still wont go into tech mode. . . I have the service...

Thanks for the reply! I dont think these have the white cam, they have the black cam on the left of the printer outside the printer chassy. . . . The white cam is on the 850 model?

I have checked the printhead for obstruction but none found! The axis moter which moves the head left and right works ok but when the printhead gets to the far left or right, it makes a horrible sound and Im guessing the motor doesnt know the printhead is as far as it will go.... this happens...

Hi all Can anyone tell me how to enter service mode on a C226? Need to investigate error H5-01. . . . Many thanks

Thanks Michael52x New belt, fuser and drums installed! I am goin to swap the printheads over and see the outcome. . .

I have a Xerox 7400 with image blur that starts off ok then will begin to print blurry from the middle of the page downwards. All toners, drums , transfer belt and fuser have been replaced!

I had suspected the dev assy for cyan was bad and I was correct! Removed the cyan dev assy and toner/dev was not distributed evenly accross the mag roller. New dev and dev assy on order. Thanks for your reply Michael52x!

I have a phaser 7760 with diagonal banding! Please see link to the example of what is supposed to be solid cyan: http://www.mediafire.com/?awwm1iuzg0o Please let me know if anyone has seen this before and what can cause this. Many thanks

I have the service bulletin SB 730 for the phaser 7300 replace or reseat toner problem. The bulletin refers to replacing the top inner cover assembly part number 116-1548-00. I am about to order this part but I just noticed this is the exact part number which is in the service manual and...

Hi all I require a fuser, feed rollers and transfer belt cleaner for the Workcentre M24 copier. This machine looks identical to the inside of a Phaser 7700 printer and wondered if the parts fit each model. Please let me know if the parts are interchangeable between machines. Also does anyone...

Hi Can anyone tell me if the following parts are the same in the following printers: 386731280 – Xerox phaser 8400 paper present flag (PL 6.0 Part 5 in 8400 manual) and 130E11550 - Xerox phaser 8550 paper present flag (PL 6.0 Part 5 in 8500 manual) Thank you

Can anyone assist with the error code 9-456? I believe the engine controller board will require replacing in order to make this machine operate again. Also, it is in my interest to replace the developer for each colour. Can anyone provide the service manual or give any advice/tips on how to...

Also, the display on the control panel is back to front. . .as if you are looking at the diplay through a mirror. . . . . Any ideas with this one? Thanks

Thanks Cultofon, Can you detail how this is done? Regards

Can anyone help me with error code 09,037.45 on a Xerox Phaser 8550? Thankyou

Can anyone tell me if the ink from a xerox phaser 850 will fit a xerox phaser 8560? Regards

Hi Can anyone tell me if the high capacity tray for a Phaser 850 will fit a phaser 8560? Regards