Search results for query: *

I was trying to find a way on the MAS to delete the log files automatically without having to manual delete the log files via the MMlogging app. I deleted the files, the original question was to have the log files delete automatically after a threshold of some sort. The MMlogging threshold is...

AtAvaya the link you provided no longer works on the Avaya Support site but thanks for the try. Kepetersen thanks for the insite of the MMLogging.exe but it acutally doesn't delete anything unless the hard drive fills up which I'm trying to avoid. I See all the verbose logging options turned on...

Current Version MM 5.2.1 sp 9 patch 3 Currently on both MAS servers their is a location for log files C:\Avaya_Support\Logs. I would like for these files to be deleted after 6 months. I have looked in the VMSC under Auditing it says Audit Event Retention days 180 but I have files that are 2...

Your not running the right command Try this command show snmp vr vr-default You can always delete the SNMP settings and setup them up how you want.

Seems like you configured the new switch into the stack wrong I have seen this happen before. It's like the stack MAC is wrong on your new switch. show logs show stacking configuration show stacking details show stacking Like w33mhz said ...Show switch would be helpful as well.

Make sure you save your configuration first before you configure stacking easy-setup because once you do that good bye configs. Also may want to look into upgrading you stacking XOS to 12.5.4.5 path 1-15 is stable. I think they have 12.5.4.5 patch 1-20 may want to check that out. You definetly...

EIGRP is a Cisco proprietary routing protocol that derived from IGRP can't use EIGRP that on Extreme...OSPF or BGP depending on your network topology. Also see your running 12.4.2.17 had some issue with this XOS version may want to looking into that as well..

The EXOS Concepts guide will explain all your stacking questions. Extreme's recommendations for stacking They all need to be the same XOS version. The XOS version needs to be installed on the same partition for each switch. The most stable stacking XOS I use is 12.5.4.5 patch 1-18

The number is a DID line. I have temporarly set the inc trk table to route the ani to a vdn then to a vector. the vector step says if ani= none disconnect. But I would really like to block all non ani calls at my trunk group or on a sytem setting. Thanks

Is there a system paramater that I can block all non ani numbers. Any help on this would be apprecitated.

Latest OTC Version 9.2.603.10000...released Feb 13 2012

System: Avaya CM 5.2.1 SP8. ISDN Trunk Group Blocking outgoing numbers no problem blocking incoming numbers that have CALLER ID/PHONE NUMBER no problem ,however when I recieve an incoming call without a Caller ID aka (no phone number. Is their someway to block all calls that have no caller...

That has been mentioned before sorry for the earlier post change your settings to this COVERAGE Keep Held SBA at Coverage Point? y External Coverage Treatment for Transferred Incoming Trunk Calls? n Immediate Redirection on Receipt of PROGRESS Inband Information? n Maintain SBA At...

Restrict Call Fwd-Off Net in the COS has to set to No not Yes.

Ok Session Manager/System Manager or Sip Enablement Server? Does your Find Me Call Me work if so you should be able to page. If it's the Enablement Server check you Map?

How are you connected to MM? QSIG SIP?

Li measurements on your trunk groups and see if you have blockage.

You can only have one TSAPI Link for Each AES server.

Try swapping out Spectralink craddle and usb cable if that doesn't work Install HAT on another PC and test. I have over 400 wirless phones and all of mine work on version 2.8.13 on XP only. Never accept upgrading the app. that could be your problem. If you did take a look at the INI file for the...

Last time I checked Hat Tool needed to be installed on an XP machine only....due to driver issues.