Search results for query: *

Well the customer is just trying to re-load the base software. They were running 12.14 and something went wrong. They were sent a 12.11 install tape with the understanding that ANY 12.xx install tape would give them the base software they required.

I have a customer that was running MM12.14 and is now trying to load MM12.11 and is running into issues. I have always been told that you can use any 12. tape as long as you are running 12.xx software, meaning you can not use a 12.xx install on a system running 13.xx software. Sorry for the...

I see a lot of the NTDW59's come through and even the NTDW61's and NTDW99's that have failed memory on them. Janaya is spot on saying most of the time it is memory failure, and memory is cheap..

I'm thinking that maybe there is something additional that I need to configure on the DHCP server for the 2033 that the 1120/1140's don't need.

I have the config file. But the 2033 unit does not contact Pumpkin and ask for the file.

I am not working with a system, I am only working off a windows based server running Pumpkin.

I have a few IP 2033 Conference units running Unistim 2310S97 and I would like to upgrade them to 2310S99. I am using Pumpkin on a Windows 2013 server that works well to upgrade my 1140's and 1120's to the newest firmware. I manually configured the 2033 with the TFTP Server IP address, it boots...

Does anyone know where I can get a copy of the 5.0 software for the 1002rp Rackmount Server?

Does anyone have a copy of the latest firmware package, or v1.40.62-0665? I have a 1006r here that I replaced the midplane in and the replacement has some outdated firmware.

Well I have tried to "Activate" windows both online and over their voice response system and I get the response "Not a valid product". Is there a certain vintage of 703t server that will only accept up to a certain release of CP? I am trying to load CP 4.0 on a NTUB06EA 703t server. I have done...

Well, the dongle is for the CP not for the OS. I have never had to install a dongle in any of the servers.

I have a couple 703t's here in my warehouse and when I do a fresh install of CP 4.0 I am getting the message "Must activate windows" after startup and logging into the system. This is the 1st time I have ever had a CP Server ask to activate windows. This is happening on different 703t's and even...

Thanks guys for all the help. Firebirdscrambler had exactly what I needed. Thank You!

The firmware is loaded onto the SSC card then pushed to the phones, I am sure it all depends on the release of the CS1000 software, but I have all the releases so I am not concerned about that, I am just lacking these specific firmware releases for these phones. I am thinking 9.4 is fairly...

thread798-1732903 Hey guys, I am looking for firmware for the M39xx sets. Particularly 9.4 for the M3904, 8.9 for the M3903, and 8.4 for the M3902. Can anyone help me out? Thanks in advance

When I place a Windows XP disk in the CDRom and boot the server, it boots up no problem at all, doesn't give any error messages at all. Boots right into the Server 2003. When I take the XP disk out and boot the server it gives me this: INVALID BOOT.INI FILE BOOTING FROM C:/WINDOWS Then the...

Hey guys, So I have 2 of these CP 1005r servers here on my bench and 1 of them came in without HDD's. So I placed 2 brand new HDD's in it, fired it up, inserted the CP 5.0 install disk for the 1005r, completed the install, and now every time it boots I get the "NTLDR is missing" error message...

Okay, apparently some of you guys are not understanding that the password on the phone has been changed. 1234# no longer works. I can not do a factory reset on the phone because 1234# is not the correct password.

Yeah I know the "Default" password. As I said, the customer changed the password.

Yes, and it asks for the password.