Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
-
help setting up office for 250 people
Is the connection for Internet or just transport to another office? 3megs isn't much for 250 people, Without knowing more I'd go with a fractional DS3 and start out around 10megs, although you need to have an understanding of what it all will cost. Go with a DS3 if you can since as it will... -
Rate_Limit
Decisions regarding what packets to transmit, which to hold and which are dropped is entirely up to the queuing mechanism being employed. On Cisco routers high speed interfaces are normally fifo but you could elect to implement fair-queuing with or without weighted random detection. These... -
single mac statically bound to multiple ports?
In a word, limiting multicasts w/o igmp/cgmp. I don't want to focus on the why, just want to know if it is possible. ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
single mac statically bound to multiple ports?
On the 2950 (SMI) is is possible to statically bind a single mac to >1 port? I didn't think this was possible but I don't have one to test. int fa0/1 port-security mac-address <mac> int fa0/2 port-security mac-address <mac> thanks, Jeff ---------------------------------------- Wasabi Pop... -
Sed or Awk question
What I want to do is to parse a file outputting everything between a line containing string and the next line containing just a \n. There will be a number of these sets in each file. Any thoughts? -Jeff bla bla bla bla bla bla bla bla string bla <---- start output bla bla bla bla bla bla...- jgercken
- Thread
- Replies: 2
- Forum: UNIX Scripting
-
Does your trunk port have to be in the same vlan in order to....
Double check your IP addressing. Try using 10.10.21.1 (router) and 10.10.21.2 (pc) with subnet mask 255.255.255.0 on vlan10 and 10.10.22.1 (router) 10.10.22.2 (pc) mask 255.255.255.0 on vlan11. Vlans are logically seperate networks with different address space. It appears as if you were... -
Err-Disabled Port
set-based switches: set port enable <port> I really don't know on the ios based switches. No shutdown in the interface config mode? -Jeff ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
Automating Cisco 4006 switch configuration
It's very easy. You instruct the script to send a string then capture the results until a certain string. I have written a Python script that opens a list of cisco devices, issues a command and records the results in a file. There's no limit to what you can do as long as you follow the... -
Wireless Point to point and vlan
Yea, that would work well. You won't even need to employ vlans. If you're 1600 has 2 eths then you don't need anything. ,-----Subnet A, Your internet internet-----Router NAT? `-----Subnet B Their internet Add ACLs preventing traffic between subnets A & B and... -
T1 Controller question
Is there a problem you're troubleshooting or is this just for curiosity? If you have an error message I can help you to decode it. T1 PRI Troubleshooting http://www.cisco.com/en/US/tech/tk713/tk584/technologies_tech_note09186a00801509d7.shtml The only reference i was able to find: If either... -
Router to Router VoIP
Can't help you without knowing what you've done. Post your configs. ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
frame relay + sub interfaces lab
The physical cabling is interface S0. The logical, or subinterfaces, use the same wires just differentiate themselves at layer 2. The frame switch doesn't have an IP, it just recieves a frame, checks it's DLCI and forwards it along that path. The endpoints are oblivious to the processs... -
EIGRP and RIP Routing Problem
Just so I get this right Site1 B Site1 A Site2 Site3 2501--eth---3620*****frame****2621***T1***7206 Since there is only 1 path to everything using routing protocols is really unnecessary. Assuming the Internet is hanging off the 7200 somewhere do this: Remove RIP and EIGRP... -
Cisco 2900 XL Question
Any router will be able to do acess-lists but, once again, I concur with BuckWeet that a firewall is what you really need. If you don't trust yourself with BSD Cisco's PIX is nice, as is Sonicwall's. ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
Wireless Point to point and vlan
That company probably won't want you to have access to their traffic, I know I wouldn't. I've done similar things and had 1 vlan for my internal traffic, 2 vlans for internet feed with custom queuing at the router. What they do with their internet is their business. BuckWeet is absolutely... -
2511 as terminal server - problem
on each line enter 'no exec'. I believe what's happening is the 2511 upon seeing there is something attached is opening an exec session and asking for a password. Also you only need to import telnet. -Jeff ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
Device does not contain a valid magic number
try dir flash: (semicolon is necessary) depending on your platform the following might also work dir bootflash: dir slot0: -Jeff ---------------------------------------- Wasabi Pop Tarts! Write Kellogs today! -
Cisco 2600 & DHCP
Yes, it's very simple. http://www.cisco.com/en/US/tech/tk648/tk361/technologies_configuration_example09186a0080094a52.shtml More detail http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca75c.html -Jeff ----------------------------------------... -
802.1q tagging problem
If you want to keep the same ID then you don't need a mapping statement. Simply set trunk 2/2 on 1020 dot1q set trunk 2/3 on 1020 isl the switch will automatically strip the isl encapsulation and add the dot1q tag. To set the default or native vlan simply add the port like normal set vlan 1...
