Search results for query: *

Hi Moriendi, here's below my display <dis-actda TYPE = stn STNO = 28500 DIS-ACTDA:STN,28500; H500: AMO ACTDA STARTED +------------------------------------------------------------------------------+ | STATION...

Hi Moriendi, Good Day I would like to ask for your help regarding my issue in CFU in an External call, I configured an Analog dummy Ext # 28500 and used the CFU to external # 90905XXXXXXX, I tried calling locally my dummy EXT # 28500 and it gave a busy tone while calling the Dummy Ext # 28500...

Thanks, I will check that...

Hi Moriendi, I would like to ask your Tech support if you experience regarding one way speech path vise versa between 4k and ISDX. We used access code then Ext #, it connects but only one way. Regards

Hi again Moriendi in addition to CCT1, I can see that some channels are used and also I performed the testing from DX side by ceasing the trunk (##80 TRK MBR and dialing the Ext #, connected to CCT1 and it went through. Is there any command from Unify that I can cease an active trk from cct1 or...

Hi Moriendi, CCT0 is already active and running, I don't want to disturb that active E1. When I activated the CCT1, I didn't even reset just the direct activate command, do you think if I can reset (deactivate and reactivate) it will change the display? Thanks for your quick reply

Hi Moriendi, I added 30 channels from the existing CDG Card unit 1 and activated, after activation some channels are already used/busy, but I noticed one thing in CDG Card display still shows P instead of A means both Circuits are active. Kindly need your advice on how to clear the alarm (P)...

Thanks, Moriendi...

Hi Moriendi, I have another issue with my Configuration Management opening the station from the Openscape 4000 assistant it's not loading. I attached the pix that I noticed in the Config Management table. sorry for a lot of queries today and thank you for your Tech support

Hi Moriendi, Thanks for your quick reply, but from the internal hunting then Ext1 manually activated the VARIABLE FORWARD to Mobile because the other employee after office hours need to answer the call using her Mobile #.

Hi Moriendi, I would like to seek your technical support regarding HUNT VCE feature, I configured HUNT in WABE (52000) and configured HUNT as VCE and used it for 2 Extn lines (Ext1 and Ext2), off hours they requested to forward the 2 Extn to Mobile, when we made the test call to 52000...

Hi, I would like to add another scenario regarding a one-way speech path call between 2 different sites analog Extn from ISDX and analog from 4K (SLAMAV) and vice versa scenario, my setup is dialing an access code 72 then 4-digit ext #, our link between the 2 sites is VOIP. Thanks

Hi, Good Day everyone, I would like to ask for your support regarding tracing a trunk (DIUT2) when accessing through Ext # and checking the status or error of your E1's. Thanks

Hi, good day guys. Thanks again for your indeed response to my queries. By the way, can I start configuring the E1 while waiting for the CDG Backplane? and I would like to confirm the Backplane part # and cable (DB9) Thanks

Thank you for your support, appreciated it.

Yes, I got COMWIN installed and at the same time accessed to the 4K. just confirming the same type of backplane DIU2 that I'm going to use for CDG Card. Thanks

wow, Thank you so much, I really appreciate your support. though got a little bit dizzy in the mnemonics commands, I'm just curious about the AMO commands regarding the installation of E1, if you can tell me where to download the AMO commands that you provided me? Thank you

not a remote shelf, yes, I got your point about the 2 X 30 channels, but each E1 will be distributed on each LTU shelf for resiliency and the other E1 will be dedicated to another location. I have ISDX DLI settings already and to be configured in RSIG.

Hi sbcsu, Thank you for your reply, 3 CDG card in slot 13 in diff shelf AP3700. (Ver 8)

Hi, I would like to seek your tech support regarding the installation and programming of CDG/PBXXXQ6401, (4K to ISDX). Thanks