Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by SIKV35

  1. SIKV35

    craftppp password reset?

    Hello Forum, We have to remote dial (modem) into our MMS v2.0 using craftppp login (then use web to access vm). However one of our technicians changed the craftppp password and we can't figure it out. We can still do voicemail actions directly on the server, however it's in another bldg...
  2. SIKV35

    How do I test ISDN circuit on Definity G3

    Thanks telecomturner! Should the signal group come up and show "in-service" on my loopback jack before I call provider?
  3. SIKV35

    How do I test ISDN circuit on Definity G3

    Trunk still OOS-NE and Sig Group still not coming up with loopback jack connected at the CSU. Tested board and all test passed. I've busied, tested and released (results passed), but still OOS-NE.
  4. SIKV35

    How do I test ISDN circuit on Definity G3

    Don't know if it's setup correctly, but typed "change sync" and something like the following came up: STRATUM: 4 Primary: 01A16 Secondary 01B18 CIRCUIT PACKS AVAILABLE FOR SYNC LOCATION TYPE NAME SYNC 01A15 DS1 DSN Y Should my new DS1 be a primary or secondary? thanks!
  5. SIKV35

    How do I test ISDN circuit on Definity G3

    My DS1 config looks like exactly like yours except "SLIP DETECTION" is set to yes and my DCP/Analog Bearer Capability: 3.1Khz. Yes, I'm using an integrated CSU. Just changed Trunk Group for Channel Selection to my trunk group. Same result...OOS-NE So is it possible to bring the Signal group...
  6. SIKV35

    How do I test ISDN circuit on Definity G3

    Just curious if I'm waisting my time trying to test my end first. Trying to make sure my end is good before contacting provider. Is it possible to bring up DS1/signal group with a loopback jack to show "in-service". Thanks!
  7. SIKV35

    How do I test ISDN circuit on Definity G3

    Done. "status sig 3" still out of service. How do I bring it up with a loopback jack? Can it be show in service with a loopback jack?
  8. SIKV35

    How do I test ISDN circuit on Definity G3

    When I change is to "n", more fields pop up: Trk board and inteface ID...also secondary D channel. How do I populate those fields?
  9. SIKV35

    How do I test ISDN circuit on Definity G3

    Thanks. Spoke with provider and we went thru our configs and same thing. Here's my ds1. Does anybody see anything wrong that my rookie eye doesn't see? TRUNK GROUP Page 1 Group Number: 1 Group Type: isdn CDR Reports: y Group...
  10. SIKV35

    How do I test ISDN circuit on Definity G3

    This is fustrating :\ I placed a loopback jack on the back of the 120A CSU and ran "test board 01A15" and all test passed. Also get status lights on front of board to match the good T1: 1 = off 2 = Yellow 3 = Off 4 = green When I do a "status Signal group 3", it states out-of-service. Same...
  11. SIKV35

    How do I test ISDN circuit on Definity G3

    What does test #139 FAIL mean?
  12. SIKV35

    How do I test ISDN circuit on Definity G3

    I did the following and passed, does it mean my end (to the loopback jack) is good? busyout board 01A15 test ds1-loop 01A15 cpe-loopback-jack = passed Haven't been able to contact provider yet. Just wanted to test my ds1 end first. Also on the front of the circuit pack, the four status...
  13. SIKV35

    How do I test ISDN circuit on Definity G3

    Flipped the transmit/receive pairs on demarc and ran "test board 01A15" and all test passed except 139 now. What does that mean?
  14. SIKV35

    How do I test ISDN circuit on Definity G3

    Yes. Using an ICSU 120A & T1 cable. Provider states their link is good. I'm looking for a way to test from my switch to demarc. will the DS1-loopback command do anything?
  15. SIKV35

    How do I test ISDN circuit on Definity G3

    Thanks guys. I "busy board 01A15, and ran a "test board 01A15" and here are the results (sorry can't copy paste screen from ASA, so re-typing results): UDS1 138 FAIL UDS1 139 thru 146 PASS ISDN-TRK 36 PASS ISDN-TRK 255 FAIL 8 ISDN-TRK 256 ABORT...

Part and Inventory Search

Back
Top