Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by redsjacketsfan

  1. redsjacketsfan

    Fax setup for IP

    I have a point to point T1 coonecting a remote site back to the switch. (Opt 81C) They use I2004 phones at that site and are connected via a 2600 and a 3550 (Cisco) to the T1. We have VGW's built and utilize Media Gateway Cards (32 port) without an actual Sig Srv (so I guess you would say we...
  2. redsjacketsfan

    CallPilot Fax Install Documentation

    It may be too late for an answer, but if you log into your CallPilot Manager GUI and on the home page select the help link, then under Administration Guides it is the first link "Administrators Guide" and it's under configuring CallPilot services.
  3. redsjacketsfan

    which ports are using on callpilot ?

    CallPilot Release 4.0 Document Number: 555-7101-202 (this is the Nortel manual, and I searched ports) TCP port 20 (FTP) TCP port 21 (FTP) TCP port 135 (DCOM) UDP port 135 (DCOM) TCP port 143 (IMAP) TCP port 389 (LDAP) TCP port 636 (LDAP) TCP port 993 (IMAP) TCP ports 1024 to 65535...
  4. redsjacketsfan

    Accessing 1000T

    Assuming you have everything configured, plugged-in etc. Enable the loop, status the loop (I do anyway), you will probably get this error "DCH1010" D-channel is disabled. LD 60 ENLL loop STAT loop Then enable D-ch should get DCH EST Time and Date, if after you status the DCH again and you get...
  5. redsjacketsfan

    Accessing 1000T

    LD 60 stat xx (loop number) enter
  6. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Preliminary results look promising I will do more testing and post results. Thanx for you help pronei.
  7. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Just got back to working this issue. Was able to do the above command per your suggestion. Now just making so calls and I'll see if it worked. I'll let you know.
  8. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Alright pronei I was able to change Customize to #1 When I type "Set" (Option) then start typing NLN, like you said the auto fill starts and I get Name (value) and this prompt populates the site name (I am sure you know this) Am I trying to change this Option Settings: HEL to NLN or do you...
  9. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Ident MDR-2000 Plus M1 Nortel Generic Rev. 3.S37.G40 Ser. N12406 Copyright (c) 1998 MDR Telemanagement Ltd. M2K> Customize (Enter) (RET - Leave entry unchanged, TAB - Remove entry, Ctrl-C - Exit command) Choices Are: #1 --> 10,18,0,26,32,41,20,3,47,53,53,53,0,0,3,0,7,0 #2 -->...
  10. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Finally got it. Date/Time (mm/dd hh:mm): 48/00 00:34 Option Settings: HEL Number of Records Stored: 000577 Records to be Collected: 000577 Port Config (PBX/Modem): 9600-8-N/ 9600-8-N Minimum Duration: 0 Incoming Calls: Yes...
  11. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Sorry, for the late response pronei FCDR old As far as MDR box, it's been set up for quite awhile (pre-my arrival) and I have no clue. No idea how to access it (actually I read the OTM stuff) but I am not very savvy with hyper-termminal or those types of Apps to access the MDR, any starting...
  12. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0 (from 7/9/08 no replies)

    Read the post from John/BSLD and ACE on the MDR 2000 and CLID retrieval from Jan/08 and I have a question. Below is the mdr2000.col script portion w/CLID from my script on OTM ; Retrieve the Calling Line ID from the call. let CheckPos = pos('D', M2KData$, FALSE) if CheckPos <> 0 then...
  13. redsjacketsfan

    MDR 2000 OTM 2.2 81C w/3.0

    Read the post from John/BSLD and ACE on the MDR 200 and CLID retrieval. Below is the mdr2000.col script portion w/CLID ; Retrieve the Calling Line ID from the call. let CheckPos = pos('D', M2KData$, FALSE) if CheckPos <> 0 then begin loop let M2KTemp$ =...
  14. redsjacketsfan

    Caller ID/Name Display NI2 protocol OPT 81C/3.0

    Sorry if I mis-spoke allenmac, I was trying to say that having only RCAP=COLP on the DCH, that calls then started working again. If I have COLP and NDS I get fast busy on the outbound calls. Thanx you 2 for the info
  15. redsjacketsfan

    Caller ID/Name Display NI2 protocol OPT 81C/3.0

    I have searched the forums and gathered quite a bit of info, and still no luck. When I make all the recommended changes (specifically when I add NDS) then do a FDL on the MSDL ckt comes back IDLE, incoming calls work (no name display, but I'll cross that bridge after this issue) But what I...

Part and Inventory Search

Back
Top