Recent content by nortelcs100e5

Hi pal, My MC32s is programmed as VGW channels, this error occurs when i created a zone1 and zone 2, i put all SIP trunks in zone2 and tried to put Mc32s in zone1, previoulsy mc32s was in zone 0. I then deleted zone -1 and EDD then restarted PBX and got every thing OK. Any advise??

Hi i am getting ERR008 4 0 5 0 8 1 5 4 randomly and call between cabinets got silent or no speech path. Then TN`s are random but this error is between cabinet to cabinet only, with cabinet ext to ext call is OK, it is cs1000e rls 5. Can somebody point a right direction to resolve this?

Hi, does it ask for overlap while setting VPIM??? and what does overlap means? regards

Can somebody briefly explain what rule should i follow to set VPIM??? i mean how to calculate/describe rule for setting VPIM prefix in Callpilot 4 or 5.?? does it related to DID range i mean lets say i have DID number ranging 5206000 to 5207900 and my extension are bulit from 6300 to 7200...

So what you guys advise about the configuration given below MGC/DB`s =Zone1 All IP sets=Zone2 SIP trunk=Zone3 MC32s=Zone4 On Site 2 MGC/DB`s =Zone4 All IP sets=Zone5 SIP trunk=Zone6 no MC32s card at other site. is that correct?? if i set IP phone zone 2 ans SIP with Zone3 then does IP...

Hi all, it is CS100E rls 5. its been in installtion phase, i programmed all analog/DLC/IP softphone ext with everything accept Zone, i didnt created any ZOne and all MGC/DB`s are programmed with no zone entered. Today i created Zone 2 and communications between got stop , call within cabinets...

Hi all. Can somebody point me how to upgrade loadware of MGC. I downloaded 6 loadware files of MGC from ESPL site and tried to load these files through Element manager Software--->Upload file but it pop an error that the file syntax should not conatin /, \, % etc and file extension must be...

Hi Thanks all for helping, I am going to do as tnphoneman advising, I was going into depth in this posty just because i wants to understand more from this forum, though i am also reading NTP`s but it is more easier to learn practical experience from this forum. Thanks and regards

I am planning to use these cards as under please advise if it is OK.(This PBX have almost all TDM stations and so mostly TDM resources will be use,another thing i didnt mentioned that i got one 96 and four 32 port DSP d/brd with this) (1) First cabinet= MGC with 96 DSP D/brd+6 PRI cards+Mgate...

allenmac , these are 11c Cabinet having 10 slot in each, it is also of SA config ,no HA. Cant i have 40 slots in 4 cabinets??? If yes then please advise how can i distribute cards and DSP D/brds in between these cabinets.

Hi Pal, look i got Five 32 port dsp daughter board with 4 MGC card and need yours assistance how to distribute thes all PRI/Analog/XUT/6 PRI in these 4 cabinets and distribution of Five 32 port dsp D/board. I am really stuck on its engineering and i need to avoid any blockage situation. Need...

The situation is that i got Five 32 port DSP D/board with 4 MGC card and I have 4 cabinet system with 195 analog, 24 digital extension,4 XUT cards and 6 PRI`s, Now can somebody advise how can i distribute these all cards with 4MGC and Five 32 port DSP D/Boards. Regards

Hi all, i need some info regarding MGC DSP usage of CS1000E. I mean with different call scenario. Can somebody answer these separately whether DSP is use or not in these call setup. (1) Analog to analog ext call within cabinet or cabinet to cabinet-->DSP is use or not? (2) Incoming DID...

Is there any product bulletin or document or some info about compatibility matrix of release 5 with SSC card and daughter board vintage and flash boot room version for release 5. this info is needed for CS1000M cabinet release 5. I was seraching on Nortel site and found some matrix but not...

Router between Callpilot and there network?? Sorry i am not a skill ful Data guy what will router do in between CP and there LAN.