Recent content by mrttn

1 more thing.... here's what my ip address and gateway ipv4 172.16.10.22 mask 255.255.255.0 default gateway 76.185.160.1 <<<<<------------ so it's using the gateway if the isp.

it's working and blow is the config. one thing though, I get error when do --ip route 0.0.0.0 0.0.0.0 76.185.174.189 (isp ip) the error said invalid hop and the ip is this router. thanks all for helping. ! ip name-server 4.2.2.2 ip dhcp excluded-address 172.16.10.1 172.16.10.21 ! ip dhcp...

thanks for all the responses. i'll try them out tonight and update the outcome.

I can remove ip nat inside source list 1 interface FastEthernet0/0 overload and worry about access-list later. 76.185.174.189 is the ip got from isp. If I were to connect my pc directly to the ips router (bypass my router) i get 76.185.174.189/19 and gateway is 76.185.x.x 76.185.174.189 is...

Hi, I am trying to config a router that sits behind my ISP. from the router, I can hit the outside world. however, I can't hit the outside world from LAN side. I also can't hit the LAN (172.16.10.22 a pc that connects to int fas0/1) I get error when add 0.0.0.0 0.0.0.0 76.185.174.189...

Hi, I am trying to use cca to config a Cisco 3500 series switch. I odd thing is that telnet works just fine. I got a login name and password and again, that same login worked when telnet in. when I try login using cisco config assistatn(cca), it's prompted for a login and that same login...

no luck, ip name-server 4.2.2.2 ! ip dhcp pool inside import all network 172.16.10.0 255.255.255.0 default-router 172.16.10.1 dns-server 4.2.2.2 ! ! bridge irb ! ! interface Loopback1 ip address 172.16.100.1 255.255.255.0 ip nat inside ! interface FastEthernet0/0 ip address...

so I make fa0/1 network 172.16.10.1 but that network is not talking to the outside world still. ip name-server 4.2.2.2 ! ip dhcp pool inside import all network 172.16.10.0 255.255.255.0 default-router 172.16.10.1 dns-server 4.2.2.2 ! ! bridge irb ! ! interface Loopback1 ip...

instead of bridging, I try loopback and now the two networks are talking but 172.16.100.1 is not talking to the outside world. see below... ip name-server 4.2.2.2 ! ip dhcp pool inside import all network 172.16.100.0 255.255.255.0 default-router 172.16.100.1 dns-server 4.2.2.2 ! ...

Minue, yes the router is behind a Verizon modem. the idea is pointing all traffic to fa0/0 and fa0/0 is also a gateway for 172.16.1.1 network. you are correct, I can just use one of the other interface but that would make it on the same 192.168.1.1 network and I don't want that. I want the...

no luck ip name-server 4.2.2.2 ! ip dhcp pool inside import all network 172.16.1.0 255.255.255.0 default-router 172.16.1.1 dns-server 4.2.2.2 ! ! bridge irb ! ! interface FastEthernet0/0 ip address 192.168.1.10 255.255.255.0 ip nat outside duplex auto speed auto ! interface...

for some reason, the 172.16.1.1 is not talking to 192.168.1.1. I can't setup virtual interface vlans on the router so I am setting up bridge instead. however, the two networks are not talking. I can ping yahoo.com from 192.168.1.1 but cannot from 172.16.1.1. I also cannot ping 172.16.1.1 from...

Hi, anyone know if there's a way I can change the default voice vlan to 1 or vice versa? thanks,

no luck. try erase config and restore and nothing works. it keep saying " no load specified" i check the uc520 and the file is there. why is the phone not picking up the file?

I have tried switching ports and those ports are configure right. I know that because the phones that are working will get that "loads file" when unplug and re-plugs. the phones that aren't working have not been used for sometime. the config file is about 400 pages, I don't think anyone would...