Recent content by kondalisa

Hi dave, thats OK, i m using this RJ45 port now, but there is a Nortel bulletin regarding using of Emphenol to RJ45 adaptor, How do i use this adaptor to connect MGATE card with CP server 600r?? Can somebody point exact connectivity of new RJ45 adaptor in a large system? i mean do i have to...

Hi,Hi it is CS1000M/81 rls 5.5. I got a new 600r rls 5 server hardware, it has RJ45 connector DS30 on it, i How can i connect server with MGATE card?? in previous hardware there was a 25 pinn D type connector through we connect to MGATE card. I was reading a bulletin regarding CallPilot MPB96...

Thanks Jack for the tips. Any more tips/advice from other???

Hi, We are going to install 02 CS1000E Rls 5.5 PBX with 100 IP ext in both PBX with SIP connectivity of both PBX and a callpilot 600r at both site.. I was reading NTP`s of planning and engineering about LAN/SIP tips and it has a lot and i cant summarize especially about LAN requirements/Tips. I...

Hi, I bought a used BCM200 from a site, but i dont know its user and password as BCM default user and password not working. How can i reset user/password to default value?? or can i recover it by reinstalling software? I would appreciate if somebody help.

Hi GH, it is a TELCO PRI and it is use mainly for incoming calls. Any more suggestions??

Hi, it is CS1000M/81c rls 5.5. I am so oftenly get following MSDL error and PRI gets disabled and after few minutes enabling/disbaling it gets OK MSDL0304 GROUP 0 MSDL 13 (2) 1911 MSDL0304 GROUP 0 MSDL 13 (2) 1926 ERR9032 3 28 14:55:09 6/05/2009 MSDL0304 GROUP 0 MSDL 13 (2) 1932 MSDL0304...

There electronic lock wont work, schedule lock wont work also i think.... Regards

Hi, it is cs1000 rls 4.5. I have a COS key on attendant console through which we changes COS of different extension on daily basis. How could i avoid attendant to change COS of some executive extensions??? I mean i dont wants attendant to change restriction of some 3 or 4 executive extensions...

Hi BI. yes there is one virtual route configure but it route number is different. I will see if TRO is set to YES of this route...What exactly does TRO/VTRO use for??? do i turn off TRO in my route if it is set to yes? wouldnt that effect any thing? Take cares

Hi, It is CS1000/81c, CPPIV, Release 5.5. I am getting the following error after every 4 or 5 minutes ERR5142 00000000 00000014 >err err5142 > ERR5142 x y Required Configurations for TRO-CM to work is missing. Check TRO( Overlay 16) and/or VTRO ( overlay 17) prompts. Where: X is the...

Hi John, it is a New ICB card with latest firmware. Are u using CP for conferencing??

any help or tip???

Hi it is CS1000M,MG release 5.5 and ICB rls 4. PBX patches are updated. Problem is that MICB is not synchronizing it times with PABX, it always gets 20 or 30 minutes ahead after every week. I resetted last week MICB due to time problem which was 28 minutes ahead from PBX and after reset it gots...

Hi Paresh, can you explain a bit more collaborative server more?? and if you dont mind can you explain briefly when we use END POINT USER and GATEWAY END POINT in NRS?? In what situation. I will appreciate if you do this for us.