Recent content by jolange77

I don't find the setting that I have to set up...

Hi, I have a problem with a SRG50 release 5 when it is in local mode due to a network failure. In normal mode, the call arrive in the SRG and it is transferred to my Callpilot on another site. If I have a network failure and the SRG is in local mode, when the call arrive, it still trying to...

Hi, How I can configure qos on vlan layer 2 (non routable). I need that packets are marked cos 2 (mapped to dscp 18). I am new with qos. Thanks!

Thank you all! I made the change on the secretary's phone and it is working!

CLS CTD FBD WTA LPR PUA MTD FNA HTA TDD HFA CRPD MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1 POD DSX VMD SLKD CCSD SWD LNA CNDA CFTD SFD MRD DDV CNIA CDCA MSID DAPA BFED RCBD ICDD CDMD LLCN MCTD CLBD AUTU GPUD DPUD DNDD CFXD ARHD CLTD ASCD CPFA CPTA ABDA...

I changed DNDA for DNDD and make a test. Still the same...

Hi, This is my phone: DES IP1120 TN 156 0 05 13 VIRTUAL TYPE 1120 CDEN 8D CTYP XDLC CUST 0 NUID NHTN CFG_ZONE 020 CUR_ZONE 020 ERL 0 ECL 0 FDN 2525 TGAR 1 LDN NO NCOS 3 SGRP 0 RNPG 83 SCI 0 SSU 0000 LNRS 12 XLST 0 SCPW CLS CTD FBD WTA LPR PUA MTD FNA HTA TDD HFA CRPD...

My problem is a CLS config: It was: CLSC DIP It must be: CLS DTN

I use 1 route separate by zone. Ex: If I want to call just in the basement, it is 5716 (57 = route and 16 = zone). I have a recorder to make 2 calls simultaneously. So my route has two members. I want to add a recorder, so I need to add a member to my route.

I did a print of the TNs and the RDB. I saw some differences. But if I'm right, what is important is the difference between the TN. Route 10 will not be used after I add the TN of the route 10 as member 3 of the route 6. Right? This is the difference: CLS DTN for: TN 004 0 01 01 MBER 1...

Hi, I have this: TYPE TLST TKTP WAT ROUT 6 DES TN 004 0 01 01 MBER 1 PAGING TN 004 0 01 06 MBER 2 PAGING I want to add this: TYPE TLST TKTP WAT ROUT 10 DES PAGING TN 004 0 00 05 MBER 1 PAG MDJ has member 3 of my route 6. When I do my change, my paging system is not...

Thank you, I found the info that I needed and made tests. With 1 kem, I can have page 1, but not with 3 kem. Up to 85 keys.

Hi! I have 1140 ip phone with 3 1100 series modules (18 keys). I'm able to use page 0 of the 3 modules, but not the page 1. Is it possible to use the page 1 on the 3 modules? If yes, I miss any configuration? TN 156 1 09 28 VIRTUAL TYPE 1140 CDEN 8D CTYP XDLC CUST 0 NUID NHTN KEM 3...

Thanks!

Hi, How can I add an IP zone for a new site (srg)? Thanks!