Recent content by eperez923

I am assuming the group call key is only on digital phones and not on analog phones, so that will not work if that is the case. I have it working with digital phones as I set up a key with the 250 extension., I guess I was just wondering if there was a way to somehow make it work with the analog...

If I remove the extension 250 from all phones and create a phantom tn of 250. Under ftr_fdn I put in all the extensions I want to ring? Does it allow you to put in more than one extension? Also, I have never created a phantom tn, what exactly do I do? DO i just create an extension on an unused...

I guess what I meant to say is that the Digital phones I have alreadt have an extension (example: 200, 201, 202, 203 etc) and another key is programmed with extension 250. THe analog lines already have an extension also (300, 301) and I am wondering if these two analog lines can be configured...

I have 5 or 6 phones set up with a DN 250. Therefore if anyone needs to get a hold of an admin they call 250. Anyways, all of these phones are M3904's is there anyway I can make two analog lines ring whenever they call this extension?

Gibblett Will this change it for the everyphone on the PBX system? Can it be done for some phones. if so? Erik

Here is what I have. I see rco is set to 0, what exactly do i need to do for this phone to cfna to 5 rings? REQ: prt TYPE: 3904 TN 4 7 DATE PAGE DES DES M3904 TN 004 0 00 07 TYPE 3904 CDEN 8D CUST 0 KBA 1 FDN 0*01726157100 TGAR 1 LDN NO NCOS 7 SGRP 0 RNPG 1 SCI 0 SSU 0010 LNRS 16...

Is there a way to make CFNA after 5 or 6 rings on an individual digital phone?

Great! I was able to see everything on ld21 and I was able to see the card on ld60. There was one other thing that I remember when this was set up. He mentioned setting it up under qsig. I did not see anything in ld 21 about qsig. Any idea where else I may be able to check this? Thanks a lot I...

I guess the way we have this working is through a E1 or T1 card on the switch. How do I see the configurations to the E1 or T1 card. other than that, this should be everything in the configuration for this network?

I guess my question now is: Te configuration I did a prt on, is that the only config for this set up or am I missing something else?

example: if I dial "4 87 334" this would dial my extension in my office. or if i dial "4 33 207" then I dialed into the nortel switch extension 207

REQ prt CUST 0 FEAT cdp TYPE tsc TSC TSC 4 FLEN 3 ITOH NO RRPA NO RLI 3 Here is the rli REQ prt CUST 0 FEAT rlb RLI 3 RLI 3 ENTR 0 LTER NO ROUT 101 TOD 0 ON 1 ON 2 ON 3 ON 4 ON 5 ON 6 ON 7 ON VNS NO CNV NO EXP NO FRL 0 DMI 3 FCI 0 FSNI 0 BNE NO SBOC NRR IDBB DBD IOHQ...

I went to ld 87 and tried to prt out tsc but had no luck. Here is what I got. MEM AVAIL: (U/P): 841827 USED U P: 473800 60628 TOT: 1376255 DISK RECS AVAIL: 429 REQ prt CUST 0 FEAT tsc ESN009 FEAT

Here is what I have. REQ: prt TYPE: dnb CUST 0 DN 4 DATE PAGE DES DN 4 TYPE CDP STCD TSC

As for the set up we are happy with it. Everything works perfect, the only concern I have is the configration for everything. What loads would show me all the configs made for this set up?