Recent content by DEEPest

I too have the same issue of static and echo bursts but on 1616 and 1608 sets at one of the sites. I too have gone through the painful process of changing 1. Combo cards ( the main board should be at firmware PCS 7 and the d/b should be at pcs 10) : REF: PCN Number: 1786B. 2. Changed the main...

Thanks pndscm for your inputs!!! Really valuable

Really appreciate your answer on this. But there would be a possibility of VM users encountering busy signals with this (broadcast hunt) setup. At your site you installed is there any such complaints? I see a section on "CPID" in the integration guide. Does this need to be programmed for this...

John, I tried building a ACD DN which forwards to the first DN of the PIMG |(supposedly the hunt DN for the VM). In this scenario : even the first caller fails (gets generic greeting instead of requesting to punch in the mailbox password). Basically, with ACD too M1 brings in the forwarding...

Integrating Cisco Unity with 81C 25.40: 2616 sets emulated to the PIMG box. Followed the procedure as per Cisco guidelines: http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/integration/pimg/guide/cucintpimg090.html#wp1060852 2616 ports are hunting/fwd'ed to the next port and so on...

Integrating Cisco Unity with 81C 25.40: 2616 sets emulated to the PIMG box. Followed the procedure as per Cisco guidelines: http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/integration/pimg/guide/cucintpimg090.html#wp1060852 2616 ports are hunting/fwd'ed to the next port and so on...

Hi, Cannot get agent Real time Display to work. It opens and closes right away. All the other RTD works i.e. skillset etc.. Have anybody encountered this issue before. The Event Viewer - Application - gives event 1000 : nicgrdsp.exe Updated all the patches but still the same.

Thanks DJ!! Well, this was before the DST in March. It's almost more than few weeks now. Thanks again. Maybe I'll try the hotfixes and see whether it makes any difference. Seems like a d/b issue in CCMA for historical reports (time) only. Strange !!

Installed a CC6 co-res. During install made a small mistake of not checking the Time zone correctly. Corrected the issue by changing the time zone accordingly. Unfortunately now the CCMS has the right time.RTD has the right time. Only when pulling the Historical reports the result is an hr ahead...

Thanks for all you guys help

I finally got it to work. CLS = MBXD should be allowed. Found it through the Nortel solutions d/b.

9201, I'll have to get the IVR guys to do that. Not sure whether they are around. John, How do you toggle supervision? Mine is set for THFD.

Absolutely, this is one of the first things I tried as the call is trasnferring from a ISDN to a TIE -DTI trunk.Tried that too John. DITI and EXTT and TRNX to "YES" but still does not work. Call works when I do ISDN to ISDN transfer for LD.

Sorry, NCOS on the IVR set is 4 and under RLI the FRL is set to 4. NCTL has FRL/NCOS set to 4. So there is not problem. Also, MFRL is set to 0 for the LD RLI. Not sure where you can list the station FRL? But as MfRL is 0 it should not matter.

What is the NCOS/FRL of the IVR Agent? NCOS on the IVR agent is 4 TGAR is 0 What NCOS/FRL does it take to make a LD call?" FRL (RLB)for the route is 2. NCOS on the members of the LD Tie route is 1.