Recent content by coolfalcon

fcpli , thank you for the note , and sorry for the misunderstanding . there was old Ericsson tool called Signal Interpreter for SLP60 Signal trace , and now its built in and exist in the MTS.

hi , to check the status for the trunks use the following command susip:rou=x,tru=all; this command before TSE6.3 new command resource_status --externals --route-number x --trunk-number 1-1..1-x --traffic-status to initiate DID number_conversion_initiate -entry xxxx -conversiontype 0...

Dear all, i have An Ianttend system connected to TSE6.3 (SIP-TRK) and the Mxone TSE6.3 is connected to another CUCM 10.5 system through Qsig Link and SIP Trunk Inattend <<------SIP TRK--->> Mxone TSE6.3 <<------SIP Trunk-->> Cisco CUCM 10.5 , when directing the calls from the Mxone to CUCM...

thanks alot. it works

dear all; i have a mxone 6.0 system , i need to stop all of types of recalled calls to the DBC4224 operator console. thank you for your help in advance

Dear all; i have a problem with our Mxone 6.0 system , i have two analog trunks , if i make two outgoing calls by a digital or operator extension if i join the two trunks on conference or make a transfer , the two called parities hear a big noise like the sound of modems , and they have a very...

thank you for your help i know how to change the Timer datablock, but my question about the value i have to change to it do i have to raise the time elapsed before the attendant to recall on no answer calls?. if set this to zero no unanswered calls will be recalled to the attendant?

Dear Gene, thank you so much for your help. i found this thread regarding the same case i posted could you please clarify the solution more . http://www.tek-tips.com/viewthread.cfm?qid=1662589 thanks alot sir

dear all i have the following problem , all the External incoming calls answered by voicemail system and then blind transfered to the attandent console (M2250). when the attendant console reply the call and transfer it to the internal extension , if the call is not answered by that extension...

this the CDR prameters of my system >ld 21 PT1000 REQ: prt TYPE: cdr TYPE CDR_DATA CUST 0 TYPE CDR_DATA CUST 00 CDR YES IMPH NO OMPH NO AXID NO TRCR YES CDPR YES ECDR NO BDI YES OTCR YES PORT 6 CNI DGTS BCAP NO CHLN 0 FCAF NO and the CDR parameters of the Pri...

see this is an internal call No problem L 107 00 5539 5962 024.1.04.09 020.0.07.01 04/01 11:13 00:00:58 0000 0000 this is incoming call from cell phone 775799299 through the Pri route 101 , 5980 is the group hunt for the auto attendant system N 023 00 T101 017 5980...

dear sir the CDR format is already OLD Format the problem i have is in Incoming call to my PBX , if one from outside call the incoming PRI route of the PBX the format of the CDR comes in two lines , the second line contains the outside calling party. see this

Dear All. we have a Nortel Cs1000M Rls4.5 system , we bought a new billing system from local provider. we have a problem with the incoming call records , the new billing system can not handle it because it comes in TWO STRINGs , the billing system only receives One sting for each record. can we...

thanks alot for your help

our system is cs1000 upgraded from option 81 . the clock controllers are connected to the refernce PRI. do you advice me to switch off the clock controller of the second shelf for a minute and then siwtch it on once again?