Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AShammah

  1. AShammah

    BCM50/FreePBX integration Sip or H.323

    Under Private/URI Map Private / Subscriber has to be empty or it will send 401;phone-context=private.subscriber in the dialplan Removing it sends 4,01 and allows calls over PRIVATE now. Updated Private oli to the ext #'s, now it passes the correct CID info
  2. AShammah

    BCM50/FreePBX integration Sip or H.323

    I'm having 1 issue with the Private trunk not sure if this is the way it sends the number when set to private but when it sends the number to FreePBX its sends as 401;phone-context=udp BCM route 005 set to public, dialing 4,01 sends 401 to Freepbx correctly. Also when I dial eg. 401 from the...
  3. AShammah

    BCM50/FreePBX integration Sip or H.323

    That clears up a lot of things for me haha Moving the hunt groups and some application DN's off of 400's is what I have to do to use 4 as dest code then it should all work seamless. I was reading through the UCX manual the instructions for connecting a SIP trunk to the BCM are pretty much the...
  4. AShammah

    BCM50/FreePBX integration Sip or H.323

    I set the inbound destinations to a page group with duplex intercom, auto answer. Could do both 89501 for duplex and 89401 to call the extension
  5. AShammah

    BCM50/FreePBX integration Sip or H.323

    I have 1 private and 1 public not sure it makes a difference from my testing FreePBX can dial 9 out over BCM and both can call extensions on both ends using private or public. It looks like theres just less SIP options using private. Did you find a way to not use dest codes when calling from...
  6. AShammah

    BCM50/FreePBX integration Sip or H.323

    I got inbound calls from BCM - FreePBX Setup an inbound route on Freepbx to accept 89xxx (dial out code on BCM - FreePBX) and routed to the corresponding FreePBX extension. I even got paging from BCM to FreePBX CallerID comes up on the FreePBX sets as anonymous. I have send long name setup on...
  7. AShammah

    BCM50/FreePBX integration Sip or H.323

    If anyone has screenshots for the setup of BCM extensions on the FreePBX side please post. Almost there, I'm just missing calls from BCM to FreePBX. Also noticed on the Cisco phones BFL for the BCM extensions shows "Red" offline but when pressed it dials fine. I'm doubting there's a way to get...
  8. AShammah

    BCM50/FreePBX integration Sip or H.323

    I got calling working from FreePBX - BCM extensions using the settings below. no prefix just dial 3xx from FreePBX and Nortel sets ring. I added each extension to the target line as "ring only" BCM - FreePBX intra calling not working yet. Working on that.
  9. AShammah

    BCM50/FreePBX integration Sip or H.323

    On the FreePBX side any string I dial out to BCM will ring the main ext 300. Calling in to FreePBX from BCM using the inbound routes above I get the FreePBX "extension is not in service" message on the BCM phone. :Solved. I needed to create a target line for each BCM extension. See target...
  10. AShammah

    BCM50/FreePBX integration Sip or H.323

    Up until last night I had "From Header Domain Match" and signaling was set to NONE I'll try changing to numeric IP.
  11. AShammah

    BCM50/FreePBX integration Sip or H.323

    Always on a Friday [upsidedown][pipe] These are my Voip.ms trunk settings. I turned signaling method from NONE to OPTIONS and incoming works now without having to dial out first. Slight delay in ringing in it used to instantly hit the BCM now theres a 1-3sec delay but at least calls are working.
  12. AShammah

    BCM50/FreePBX integration Sip or H.323

    "from-internal" should do it. I reverted most of my Freepbx setup yesterday trying to get inbound calls working again on the BCM but that was all I had different. I was had two trunks with two outbound routes "from-trunk" with no prefix, "from-internal" with prefix. From BCM I can dial 89+401...
  13. AShammah

    BCM50/FreePBX integration Sip or H.323

    Sorry for the confusion. Is DISA working?: DISA is not working. kept getting DISA invalid entry then AA played after. DISA is off now. Are the Door Phones working?: Doorphones are working Are all Voip Trunks working?: All trunks are working now that I set Nat pinhole options to 30, slight...
  14. AShammah

    BCM50/FreePBX integration Sip or H.323

    This post just saved me from resetting the BCM and starting over from scratch. https://www.tek-tips.com/threads/voip-ms-delayed-inbound-issue-with-did.1812521/ Changed ITSP “from header proxy address match” didn’t help. I turned signaling method on to “options/30” to give it a tap It’s...
  15. AShammah

    BCM50/FreePBX integration Sip or H.323

    Now having an issue where if I call in to the voip.ms trunks it hangs then disconnects no ring. If i use the trunk to make an outgoing call I'm able to make inbound calls to the trunk for a few minutes then its back to no incoming calls across all trunks. I have to make an outgoing call from...

Part and Inventory Search

Back
Top