Why does my OPT11C have a DTR programmed on slot 1? 1

[M1north]

For some reason only 1/20 PBX I manage has this programmed on slot 1.

REQ: stat 1
00 DSBL 00 BUSY TDS
00 = IDLE (DTR)
01 = IDLE (DTR)
02 = IDLE (DTR)
03 = IDLE (DTR)
04 = IDLE (DTR)
05 = IDLE (DTR)
06 = IDLE (DTR)
07 = IDLE (DTR)

** Option 11C CPU Status **
SRAM: 128 kBytes
DRAM: 16 MBytes
Program Store: 32 MBytes
Flash Drive: 16 MBytes
Single fibre expansion board #1 installed.
Expansion board #2 not installed.
PCMCIA card installed in drive A.
PCMCIA card not installed in drive B.


.****
>ld 22
PT2000

REQ iss

MAIN CAB
VERSION 2111
RELEASE 25
ISSUE 40 B +

 

[bhassell2000]

is there a DTR card in slot 1?

my 11s have the DTS on slot 0 on the SSC card


REQ: stat 0
00 DSBL 01 BUSY TDS
00 = IDLE (DTR)
01 = IDLE (DTR)
02 = IDLE (DTR)
03 = IDLE (DTR)
04 = IDLE (DTR)
05 = IDLE (DTR)
06 = IDLE (DTR)
07 = IDLE (DTR)


Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[M1north]

I dont think so....now I`m wondering if this is an older cabinet and the SSC card is slotted in slot 1?

 

[bhassell2000]

what happens when you stat 0? or do a card inv in ld 117?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[Triton101]

prt your cequ in ld 20
see what it has for conf/tds loops.



__________________________________________________________
Find a job you love and you'll never work a day in your life. - Confucius

 

[M1north]

CEQU
MPED 8D
SUPL 000 004 008 012
016 032 036 040
044 048 064 068
072
XCT 01
CONF 029 030 031 062
094 095

DLOP NUM DCH FRM LCMT YALM T1TE TRSH
PRI 09 24 ESF B8S FDL - 00
MISP

 

[DocVic]

DLOP all the way out in slot 9 ??? This must be an older Option 11, right!? Normally the DTR's are on the SSC card in Slot 0, then PRI in Slot 1, Trunk, Digital, then Analog...
What version of software does this machine have?

DocVic
Dedicated to Nortel Products till the end.
Need help?

http://www.TSS-CO.com

 

[Firebird Scrambler]

When the Option 11 was upgraded, the procedure for deleted the DTR /XTD TN's and creating them onto slot 0 weren't used.


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[M1north]

OK, so does this mean I have to move the card to slot 0 and then delete and re-create them in slot 0?

 

[M1north]

Another question:

If I archive this database and then restore it on another 25.40b switch, will the DTR programmiung change the new PBX?

The new one is currently programmed on slot 0

thx

 

[DocVic]

Yes it will.

DocVic
Dedicated to Nortel Products till the end.
Need help?

http://www.TSS-CO.com

 

[Firebird Scrambler]

DTR's and XTD's (XTD's are used in the UK) will just need programming onto the SSC card in slot "0". You won't need your existing card as it was all built into the SSC.

From what I remember, you disable the slot 1 DTR card in LD 34 as e.g. DISR 1?. Remove all DTR's in LD 13. Build in the new ones from e.g. 0 0 to 0 7 etc. Enable the DTR's in LD 34 as e.g ENLR 1 etc.

We always did this in conjuction with the removal of TTY'1 and 2 and then re building them against slot "0".


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.