Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

where is the parameter?

Status
Not open for further replies.

Monrovia

Technical User
Mar 1, 2007
292
IN
can somebody tell me where is the parameter to change sending digits when dialing out? delay the time of digits send from pbx

i have problem that, before completing the dialing of external numbers, it start ringing somewhere - some wrong numbers. i understood that, it is because, the number which i dialed has not completed, and the pbx send the digits.

pls somebody help me
 
in one route, after dialing the route access code, 166, i can wait for around 10-20secs without dialing any other digit, so that i can have look the number in mobile or paper and then dial it.

and in other route, after dialing route access code 158, i cannot wait that much, just abt 5sec or less than that. it disconnects the line.
 
Check if you are sending NBLOC or overlap, set to NBLOC and set MIN MAX values.

Monrovia too

 
hi bija

ROCAP:ROU=ALL;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 7131000000000010 5 2100000001 0 30 128 00151515 211110000030 001100
158 7110000000000010 5 3110000000 0 30 128 00151515 511110020031 111111
166 7110000000000010 5 3110000000 0 30 128 00151515 511110020031 111111

<RODAP:ROU=ALL;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 SL60 H'00000010 H'10020000 H'00010000 NO
158 SL60 H'00000310 H'15420000 H'46300000 NO
166 SL60 H'00000310 H'15420000 H'06300000 NO

<RODDP:DEST=9&00&88;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
9 1 0005000000000250000000000 0 2 0
00 158 0606100000000250001000000 0 1 0
88 166 0606100000000250001000000 0 1 0

In this route 1&166 dont have problems. route 158/Dest 00 has the problem as i said.

hi GFdanna user,

where to check this NBLOC and overlap? pls advice me
 
hi,

note VARO in both dest. 166 & 158

158 SL60 H'00000310 H'15420000 H'46300000 NO
166 SL60 H'00000310 H'15420000 H'06300000 NO

regards
 
I have the exact same problem. I don't know if the same settings could apply to me?.

[tt]
<ROCAP:ROU=8;
ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

8 0110000000000010 5 2100000010 0 30 128 00151515 311100000030 111100

END

<RODAP:ROU=8;
ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

8 SL60 H'00000310 H'00000000 H'00400000 NO

END


<RODDP:DEST=6;
EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

6 8 0005000000000250000000000 0 2 0
[/tt]

Any help would be fully appreciated!
Thanks
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top