Wave-Off for Outbound Calls on PRI

[velcrobomb]

I just turned up a PRI with Verizon and cut over my DID trunks and CO trunks to point to this T-1. Incoming calls are working fine. However, when I try to outbound dial I get a wave-off from the switch.

Does anyone have a Verizon PRI that I can get some protocol settings from? Verizon doesn't seem to know what they are supposed to be.
(G3siR6)
N12
ESF
B8ZS
Service Type: pub-net
Codeset to Send: 6 Codeset to send TCM, Lookahead: 6
Max Message Size: 244
Supp: a Digit Handling: enbloc/enbloc
Trunk Hunt: Descend

DS1 Parameters:
Country = 1
Protocol : b

 

[sezwhat]

Are you in Ex-BA or Ex-GTE Territory ?

 

[n00benduser]

do a disp trunk-group XXXX (XXXX = your trunk number) and paste the info.

 

[velcrobomb]

Ex-GTE for the first question.

Can't attach files, so here's a paste:

TRUNK GROUP
Group Number: 4 Group Type: isdn CDR Reports: y
Group Name: WesternU Local COR: 62 TN: 1 TAC: 804
Direction: two-way Outgoing Display? y
Dial Access? y Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send TCM,Lookahead: 6
Max Message Size to Send: 244 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: descend
Connected to Toll? n STT Loss: normal DTT to DCO Loss: normal
Calling Number - Delete: Insert: Numbering Format: natl-pub
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
G3R6: display trunk-group 4 (page 2) 3/5/2004 1:46:27 PM
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n Send Connected Number: y
Suppress # Outpulsing? n Numbering Format: unknown
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Send UCID? y
Send Codeset 6/7 LAI IE? n

 

[sezwhat]

I only see one difference from my setup, under TRUNK FEATURES mine is set up for Numbering Format: public.

 

[velcrobomb]

Actually, I had it set to public before. The change to unknown was to try and troubleshoot the problem.

 

[n00benduser]

whats the carrier medium?

 

[sezwhat]

Does the command "list trace station" work on R6? I've used that to troubleshoot outbound issues before.

 

[velcrobomb]

No option for carrier medium that I know of and r6 does not have the option for list trace station. (The board is TN767C)

 

[velcrobomb]

It may be worth noting that I'm using an Adtran external CSU. Any thoughts? Inbound calls are fine.

 

[velcrobomb]

I figured out the problem. In the route pattern, the numbering format must be set. When I had it set to natl-pub, it waved off. I set it to locl-pub and it worked. I also set it to unknown and it worked.

Thanks for all the replies.