Specs:
DUAL BOOT WIN98SE & W2K SERVICE PACK 2
INTEL PIII 500MHZ
FAMILT 6 MODEL 7 SEPPING ID 2
SLOT 1 (SC242 CONNECTOR)
DFI M/B: P2XBL REV. D1 (UPDATED BIOS)
FLASH BIOS: AWARD MODULAR BIOS V4.51PG
ID: 05/30/2000-I440BX-FD-2A69KD4FC-00
CHIP SET: INTEL 440BX/ZX REV 3 (UPDATED CODE)
(DMI VERSION 2.2/LATEST 2.3)
NOT SURE HOW TO UPDATE THIS
HDD: WD400BBRTL "using EZ-BIOS TO RUN"
WESTERN DIGITAL 40GIG ATA100
PARTITION 1 C:WIN98/FAT32--2GIG,
2 D:W2K/NTFS--8GIG, 3 E:STORAGE/NTFS
ATI RAGE 128 AMR V2.0
WIN98 WORKS FINE
PROBLEM:
W2K LOADS TO THE USER LOGIN SCREEN. WHEN I PUT IN MY PASSWORD IT CYCLES FROM LOGIN TO LOADING SETTINGS, SAVING
SETTINGS, INPUT USER SCREEN AGAIN.THE RESULTS ARE THE SAME ALL USERS. ALL LOADING MODES SAFE MODE,DEBUG,LAST KNOWN GOOD, ADMIN... NEVER LOADS PASSED THIS LOOP.
THIS ISSUE SPAWNED FROM DOWN LOADING THE W2K SERVICE PACK 2. AFTER DOWN LOADING I GOT STOP ERROR 0X7B. ( 0X0000007B (0XED41B84C, 0XC0000034, 0X00000000, 0X00000000)) TURNED OUT TO BE PIN ISSUE ON HDD DO TO NEW DRIVER IN SP2.
AT THIS TIME I UPDATED BIOS, CHIP SET ETC... FIXMBR......TRIED TO MAKE A BOOT FLOPPY TO BYPASS. CHANGED THE ERROR CODE TO OR CORRUPT NTOSKRNL.EXE FILE WHEN BOOTING FROM FLOPPY "ONLY". I REPLACED THIS FILE THRU RECOVERY CONSOLE. WITH FILE FROM W2K CD. I THINK THE SP2 UPDATED THIS FILE.... ISSUE?...SINCE I REPLACED WITH OLD FILE?
*FYI **AS A NOTE WITH 0X7B ISSUE: THE RECOVERY CONSOLE WORKS BUT THE W2K SETUP CAN NOT FIND VALID W2K TO REAIR OR REPLACE. HDD DRIVER UPDATED BY SP2. MAXTOR (A 17G)AND WESTERN DIGITAL (40GIG)DRIVES THAT ARE INSTALLED USING THE ALTERNATE PIN SETTINGS MUST BE RESET TO STANDARD PIN SETTINGS AFTER INSTALLING SP2. TO WORK.
ALTHOUGH WIN98 WORKS FINE WITH BOTH SETTINGS
THANKS FOR LOOKING, ANY INFO, LINKS,
I CAN’T SEEM TO FIND ANY THING.
THANKS AGAIN,
X2
DUAL BOOT WIN98SE & W2K SERVICE PACK 2
INTEL PIII 500MHZ
FAMILT 6 MODEL 7 SEPPING ID 2
SLOT 1 (SC242 CONNECTOR)
DFI M/B: P2XBL REV. D1 (UPDATED BIOS)
FLASH BIOS: AWARD MODULAR BIOS V4.51PG
ID: 05/30/2000-I440BX-FD-2A69KD4FC-00
CHIP SET: INTEL 440BX/ZX REV 3 (UPDATED CODE)
(DMI VERSION 2.2/LATEST 2.3)
NOT SURE HOW TO UPDATE THIS
HDD: WD400BBRTL "using EZ-BIOS TO RUN"
WESTERN DIGITAL 40GIG ATA100
PARTITION 1 C:WIN98/FAT32--2GIG,
2 D:W2K/NTFS--8GIG, 3 E:STORAGE/NTFS
ATI RAGE 128 AMR V2.0
WIN98 WORKS FINE
PROBLEM:
W2K LOADS TO THE USER LOGIN SCREEN. WHEN I PUT IN MY PASSWORD IT CYCLES FROM LOGIN TO LOADING SETTINGS, SAVING
SETTINGS, INPUT USER SCREEN AGAIN.THE RESULTS ARE THE SAME ALL USERS. ALL LOADING MODES SAFE MODE,DEBUG,LAST KNOWN GOOD, ADMIN... NEVER LOADS PASSED THIS LOOP.
THIS ISSUE SPAWNED FROM DOWN LOADING THE W2K SERVICE PACK 2. AFTER DOWN LOADING I GOT STOP ERROR 0X7B. ( 0X0000007B (0XED41B84C, 0XC0000034, 0X00000000, 0X00000000)) TURNED OUT TO BE PIN ISSUE ON HDD DO TO NEW DRIVER IN SP2.
AT THIS TIME I UPDATED BIOS, CHIP SET ETC... FIXMBR......TRIED TO MAKE A BOOT FLOPPY TO BYPASS. CHANGED THE ERROR CODE TO OR CORRUPT NTOSKRNL.EXE FILE WHEN BOOTING FROM FLOPPY "ONLY". I REPLACED THIS FILE THRU RECOVERY CONSOLE. WITH FILE FROM W2K CD. I THINK THE SP2 UPDATED THIS FILE.... ISSUE?...SINCE I REPLACED WITH OLD FILE?
*FYI **AS A NOTE WITH 0X7B ISSUE: THE RECOVERY CONSOLE WORKS BUT THE W2K SETUP CAN NOT FIND VALID W2K TO REAIR OR REPLACE. HDD DRIVER UPDATED BY SP2. MAXTOR (A 17G)AND WESTERN DIGITAL (40GIG)DRIVES THAT ARE INSTALLED USING THE ALTERNATE PIN SETTINGS MUST BE RESET TO STANDARD PIN SETTINGS AFTER INSTALLING SP2. TO WORK.
ALTHOUGH WIN98 WORKS FINE WITH BOTH SETTINGS
THANKS FOR LOOKING, ANY INFO, LINKS,
I CAN’T SEEM TO FIND ANY THING.
THANKS AGAIN,
X2