VTC TROUBLES IN 7.0 1

[JarHead2078]

I have a CS1000M that I have set up for ISDN BRI service to work with some VTC equipment. I cannot get it to see a layer 2 connection. The verzion of software on the system is 7.0. I am starting to wonder if I have a card release and software incompatability isse. If any one can give me some direction on this it would be great. I have included the captures of the build below;

ld 27

BRI000
MEM AVAIL: (U/P): 43052757 USED U P: 8313483 263837 TOT: 51630077
DISK SPACE NEEDED: 346 KBYTES
TNS AVAIL: 63848 USED: 1687 TOT: 65535
BRI DSL AVAIL: 9996 USED: 4 TOT: 10000
REQ prt misp
DCH: 35 MAINT INDICATION TIME: 10:30:37
COUNTER VALUE
3 95
19 255



SCH2100
REQ prt

TYPE misp

LOOP 8


LOOP 8
APPL BRIL
DPSD NO
CARD1 24 1 15
CARD2 20 1 15
CARD3
CARD4

REQ prt

TYPE card

TN 24 1 15



TN 24 1 15
MISP 8
CTYP UILC


REQ prt

TYPE dsl

DSL 24 1 15

DATE

PAGE

DES

NACT



TN 24 1 15 0
DES 620VTC
CUST 0
ERL 0
CTYP UILC
OPT BRIL
MISP 8
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 1
NCOS 5
SCPW
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 2 FEB 2012


TN 24 1 15 1
DES 620VTC
CUST 0
ERL 0
CTYP UILC
OPT BRIL
MISP 8
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SCPW
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 26 JAN 2012


TN 24 1 15 2
DES 620VTC
CUST 0
ERL 0
CTYP UILC
OPT BRIL
MISP 8
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SCPW
SGRP 0
CLS CTD ICDD CDMD MRD ABDD PGND BRTD
DATE 26 JAN 2012

REQ prt

TYPE tsp

DSL 24 1 15

SCH0120
DSL 24 1 15 0

OPT



USID 1
MPHC NO
SPID 4760
4762

DN 4760 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 4762 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 4760

REQ prt

TYPE tsp

DSL 24 1 15 0

OPT spid

SPID 4760



USID 1
MPHC NO
SPID 4760
4762

DN 4760 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 4762 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 4760

REQ SCH0600
REQ prt

TYPE tsp

DSL 24 15 SCH0123
DSL 24 1 15 1

OPT spid

SPID 4763



USID 1
MPHC NO
SPID 4763
4764

DN 4763 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 4764 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 4763

REQ prt

TYPE tsp

DSL 24 1 15 2

OPT spid

SPID 4771



USID 1
MPHC NO
SPID 4771
4778

DN 4771 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DN 4778 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTA FND SFD CFTD MWD FBD CFXD DNO3 DNDY
SSRV_NI

DFDN 4771

REQ end



>ld 20


PT0000
REQ: stat 25 1 15


NPR086
TIM059 10:33 3/2/2012 CPU 0

REQ: stat 24 1 15


SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE RLS 0 UP
01 = IDLE LINE RLS 0 UP
02 = IDLE LINE RLS 0 UP
03 = UNEQ
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ
REQ: end

>ld 22

PT2000

REQ prt

TYPE cequ


CEQU
SUPL 004 012 020 024
028 V096 N156
SUPC
SUPF
XCT 000 016 032 048
CONF * 001 * 017 * 033 * 049

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
PRI 002 24 ESF NO B8S FDL 00
003 24 ESF NO B8S FDL 00
010 24 ESF NO B8S FDL 00
011 24 ESF NO B8S FDL 00
018 24 ESF NO B8S FDL 00
019 24 ESF NO B8S FDL 00
034 23 ESF NO B8S FDL 00
035 23 ESF NO B8S FDL 00
DTIC 036 037 038 039
040 041 042 043
044 045 046 047
052 053 054 055
058 059 060 061
062 063
DTI2
MISP
008
EXT0 3PE
CNI 009 000 000
CNI 009 001 001
CNI 010 000 002
CNI 010 001 003
CNI 011 000 004
CNI 011 001 005
CNI 012 000 006
CNI 012 001 007
EXT1 3PE
CNI 009 000 000
CNI 009 001 001
CNI 010 000 002
CNI 010 001 003
CNI 011 000 004
CNI 011 001 005
CNI 012 000 006
CNI 012 001 007
MCFN 509 MB

REQ end

>ld 97

SCSYS000
MEM AVAIL: (U/P): 43052757 USED U P: 8313483 263837 TOT: 51630077
DISK SPACE NEEDED: 346 KBYTES
REQ prt

TYPE supl

SUPL 8

SCH5739
SUPL


SUPL SUPT SLOT XPEC0 XPEC1 SHLF ZONE0/1 IPR0/1

004 STD LEFT 07 0 3 -- - - --- --- - --- ----------
012 STD LEFT 01 0 3 02 0 3 --- --- - --- ----------
020 STD LEFT 08 0 3 09 0 3 --- --- - --- ----------
024 STD LEFT 03 0 3 04 0 3 --- --- - --- ----------
028 STD LEFT 05 0 3 06 0 3 --- --- - --- ----------
096 ---- ---- VIRTUAL -- - - --- --- - --- ----------
156 ---- ---- PHANTOM -- - - --- --- - --- ----------

REQ end

 

[JarHead2078]

Does anyone see anything that might help?

 

[111SCOI]

I wish that I could help you, but I am even more stuck than you are. When I Stat my UILC, all my L1's show as DOWN. Hopefully someone will respond to your post which should help me out as well.

 

[rcsweet]

Below is one DSL/TSP I use for VTCs.
I have not had any programming problems from any VTC vendor(s).

This bigest problem is that the USER'S SPIDs are not programmed
on the correct VTC port. This can be checked by having the User
unplug each RJ-45 from the VTC equip. one at a time, then STAT the
DSL Card. This will show that L1 being down. If the correct SPIDs
for that DSL are not received L2 will never comeup.
I use two user in TSP. This will insure that each SPID/NUMBER will
use a full 64K B-channel and not sharing a B-channel

If L1 will not come up, the problem is the DSL Card is not seeing
the NT-1. (User equipment OFF or bad cabling)


============ DSL ===============
TN 56 1 6 0
DES AnyPBX
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 3
FDN
EFD
HUNT
EHT
TGAR 1
NCOS 7
SCPW
SGRP 0
CLS UNR ICDA CDMD MRD ABDD PGND BRTD PRMD
DATE 28 JUL 2011


======== TSP for DSL 56-1-6-0 =========

USID 1 <----- This # will get B-Channel @ 64k
MPHC NO
SPID 5551112222 <--- SPIDs can be any #
DN 1112222 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP YES
TRANS YES
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 1112222


USID 2 <---- This # will get 2nd 64k channel
MPHC NO
SPID 5551113333
DN 1113333 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP YES
TRANS YES
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 1113333




'============ Card Status =================
L1 = UP Card and NT-1
L2 = RLS User has not transmited correct SPID
L2 = ESTA At lease one SPID has been received
#TEI = Number SPIDs User correctly Xmited

SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE RLS 0 UP
01 = IDLE LINE ESTA 2 UP <--- Both SPIDs received
02 = IDLE LINE RLS 0 UP
03 = UNEQ
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ

 

[111SCOI]

Thanks 'rcsweet' for the response, it helped me to understand this a bit better. I do have a couple more questions for you.

1. I intend to use six channels in order to acheive 384K throughput, so do I increment my USIDs from 1 to 6, and for my second VTC do I continue with 7 to 12?
2. Also I noticed that you used PRID 3, is this what I should be using for a Polycom (ISDN) VTC?

Thanks again for you help.

 

[rcsweet]

1. Each DSL/LEN use USID 1 & 2 because one LEN has
no bearing on the other.

2. This is the profile/protcol (determined by the SPID recved)
that communications between the LEN and the VTC equipment
Both ends must match. All Polycom that we use support DMS.
If is older VTC equip. this may have to be changed.

 

[JarHead2078]

I've tested each DSL by unplugging the corresponding the corresponding line and L1 goes down when I STAT the DSL. When I reconnect it L1 goes up when I STAT the DSL. I am going to do a force load on the MISP and see if that changes anything.

 

[rcsweet]

You may want to Google the following NTP 553-3001-518
(don't Avaya's #) tile ISDN BRI Maintenance. It has
step-by-step trouble shooting info. and Loop-Back info.

Remember that the VTC equip must send the correct SPIDs
to the correct TN.

 

[JarHead2078]

Thanks for all the help. I did a FDL of the MISP card and everything is working fine now.