VOICE ERROR: Bearer capability not available(0x3A): bchan -1, call id 0xBC18

[phonetech2012]

We have 2 pri's thru time warner and all of a sudden are experiencing failed incoming calls. When we call from certain cell phones, and supposedley certain land lines we get a redirect message saying "welcome to verizon wireless, your call can not be completed at this time...blah blah. Then the same call might go thru after a few more tries.
I do not even see this call hitting my pbx (cs1000 rls7.0). TW is saying the pbx is rejecting the call, which might be if CLID info is not being sent out, right? Call trap is below. Any ideas,?, because I doubt very much this is my pbx causing this. Thanks

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98383

Exclusive, Channel 3

Facility i = 0x9F8B0100A117020113020100800F574952454C4553532043414C4C4552

NYCLNYPMRT001#

Protocol Profile = Networking Extensions

0xA117020113020100800F574952454C4553532043414C4C4552

Component = Invoke component

Invoke Id = 19

Operation = CallingName

Name Presentation Allowed Extended

Name = WIRELESS CALLER

Display i = 'WIRELESS CALLER'

Calling Party Number i = 0x2180, '7328504422'

Plan:ISDN, Type:National

Called Party Number i = 0x80, '3464'

Plan:Unknown, Type:Unknown

NYCLNYPMRT001#

Jun 7 14:30:51: ISDN Se0/0/1:23 Q931: TX -> SETUP pd = 8 callref = 0x1D42

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98383

Exclusive, Channel 3

Facility i = 0x9F8B0100A117020113020100800F574952454C4553532043414C4C4552

Protocol Profile = Networking Extensions

0xA117020113020100800F574952454C4553532043414C4C4552

Component = Invoke component

Invoke Id = 19

Operation = CallingName

Name Presentation Allowed Extended

Name = WIRELESS CALLER

Display i = 'WIRELESS CALLER'

Calling Party Number

NYCLNYPMRT001# i = 0x2180, '7328504422'

Plan:ISDN, Type:National

Called Party Number i = 0x80, '3464'

Plan:Unknown, Type:Unknown

NYCLNYPMRT001#

Jun 7 14:30:55: ISDN Se0/0/1:23 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.

Jun 7 14:30:55: ISDN Se0/0/1:23 **ERROR**: call_cleared: VOICE ERROR: Bearer capability not available(0x3A): bchan -1, call id 0xBC18

NYCLNYPMRT001#

Jun 7 14:31:01: ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x6557

Cause i = 0x8190 - Normal call clearing

Jun 7 14:31:01: ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0xE557

Jun 7 14:31:01: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x6557

NYCLNYPMRT001#u all

All possible debugging has been turned off

NYCLNYPMRT001#

 

[smokinjoe2938]

this sounds like the telco provider problem, is this a new pri? if not then ask them why it quit working,especially if no programming changes were made.

acss sme acis sme acss cm 5.2.1 acss cm and cmm acss aura messaging.

 

[PERRYPJ]

IF YOU TURN ON THE DCH MESSAGING AND YOU DON'T SEE ANYTHING ON THE MSGI, THAT CALL IS NOT HITTING THE SWITCH

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[VTTD1870]

Similar problem but do not know how to turn on d-channel msging from UCM.