Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
VmPro limit
- Thread starter Kkiyuu
- Start date
amriddle01
Programmer
No you can't I'm afraid, you can however reserve some for checking voicemail and announcments 
ACSS (SME)
APSS (SME)
ACSS (SME)
APSS (SME)
IPOfficeIreland
Technical User
put queuing with a call limit on the incoming call route using Manager.
How are you using the module?
Goes the ICR directly to a module?
Are you using SIP?
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
Goes the ICR directly to a module?
Are you using SIP?
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
- Thread starter
- #5
No.
The installation is very simple. Imagine, I have 2 modules and my idea is use 2 channels with one module and the rest 2 for the other module.
My problem is the first module have more traffic and sometimes its using the 4 ports.
How is the best way to test first to enter the call to VMPRO if all the ports are running?.
Best regards.
The installation is very simple. Imagine, I have 2 modules and my idea is use 2 channels with one module and the rest 2 for the other module.
My problem is the first module have more traffic and sometimes its using the 4 ports.
How is the best way to test first to enter the call to VMPRO if all the ports are running?.
Best regards.
Yes ok, but how is a call send to the Module?
Does it dial an external number, or do internal users dial a shortcode?
If you're using SIP the you can put that on 1 channel, or like TheTaker says use the Q of a HG to limit the calls.
It all depends on how you've set it up and use it.
More info needed!
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
Does it dial an external number, or do internal users dial a shortcode?
If you're using SIP the you can put that on 1 channel, or like TheTaker says use the Q of a HG to limit the calls.
It all depends on how you've set it up and use it.
More info needed!
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
- Thread starter
- #7
Sorry.
No using SIP lines. Only use VMPRO for incoming calls (external numbers).
WIth this information you can help me about:
- Can I create a module that this use only 2 VMPRO ports?.
- How is the best way to test if all the 4 VMPRO porta re in use?
Thanks for your help.
No using SIP lines. Only use VMPRO for incoming calls (external numbers).
WIth this information you can help me about:
- Can I create a module that this use only 2 VMPRO ports?.
- How is the best way to test if all the 4 VMPRO porta re in use?
Thanks for your help.
Create a phantom user with a fwd unconditional to a shortcode (your module)
Create a HG put in the phantom user and put the Queue limit to 1.
Turn VM on, on the HG, in VMPro connect the start point to a disconnect or whatever. So now the second call goes to VM if the Q-limit is set to 1.
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
Create a HG put in the phantom user and put the Queue limit to 1.
Turn VM on, on the HG, in VMPro connect the start point to a disconnect or whatever. So now the second call goes to VM if the Q-limit is set to 1.
___________________________________________
It works! Now if only I could remember what I did...
Dain Bramaged
___________________________________________
- Thread starter
- #9
- Status
