Virtual Calling Card facility

[a4238468]

I have configured a route (using Analog lines as trunk members) for the users who want to use calling cards to make Local , STD/ISD calls.

Above is working for normal analog sets but when i am using 3900 series sets i am prompted for redialling the card number (stating that the card number is invlaid) even though I have keep dialling the same, eventually a message comes "yu have exceeded your time limit" & I have to redial the same card number with same result.

 

[johnpoole]

look at a few things, eod timer and ees settings. either can cause the problem, if ees is no, then the far end does not see any digits, but can dial from an analog, with eod timer to short, the far end does not see all digiits. if bars is not complete, ie spn bars, that problem can't be fixed.. the switch has to know how many digits to route on and how long to expect additional digits.. dial 9 plus a did, answer that call and attempt to dial the cc number post answer supervision. that is a fair test of how many, if any digits the far end is getting

john poole
bellsouth business
columbia,sc

 

[acewarlock]

Try dialing with a 3900 type set and after dialing the last digit in the phone number hit the # and then see if it takes the password. If it works than the EODT is to long.

 

[johnpoole]

ace, it seems like everyone is off today but us and people who ask a question and leave us hanging. something i pick up a while back, if bars is not set up right, then the idt has to time out before the eodt timer starts.. makes sense, you dial. 9 xxx xxxx, if the switch doesn't have the data to process that call imm after the last digit, it waits for the inter digit, that starts the end of dial timer, even more delay added via incomplete bars

john poole
bellsouth business
columbia,sc

 

[a4238468]

Thanks a lot for the reply , I have worked on the solution provided by acewarlock but it's still giving the same message "you have exceeded your time limit please put the card number again"

Below is the detail procedure which I am using to make a call.

9 - to access the configured route

dial the following number of the calling card company

1602102

(till this point everything works fine for both digital & analog phones)

after that i got the prompt to dial the card number now when dial the same thru analog phones it prompted me for password & after that i am able to make any call.

when dialling the card number thru digital phone remote system doesn't seem to understand as it again prompt me for the same & then gives the above message.

Below is my route configuration.

TYPE RDB
CUST 00
DMOD
ROUT 14
DES COT
TKTP COT
NPID_TBL_NUM 0
PRIV NO
RPA NO
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 7888
TARG
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
ARP 3
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DDO NO
CDR NO
CCO NO
NATL YES
SSL
CFWR NO
IDOP NO


PAGE 002

MUS NO
MR NO
PANS YES
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
MCTS NO
ALRM NO
ART 0
TIDY 7888 14
SGRP 0
AACR NO

I am still working on the solution provided by Johnpoole

 

[johnpoole]

let me know if you need any help on that

john poole
bellsouth business
columbia,sc

 

[acewarlock]

EES= YES in LD 15 CDB

 

[a4238468]

Thanks a lot guys I have decreased the EOD value & it starts working fine but tell me this value affects only digital not the analog phones ?

 

[johnpoole]

on analog phones, the dtmf is generated in the dial pad as opposed to the dtr card, you can call and talk for an hour and still have a live dialpad

john poole
bellsouth business
columbia,sc