Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Vacant Number Routing Question

Status
Not open for further replies.

ramtel

IS-IT--Management
Apr 20, 2006
68
US
I'm not sure this is doable, but I'll throw it out here and maybe someone has an answer.
I have two sites with 81's connected by fiber. Site A has all the incoming DIDs and by using DSC I route calls to extensions programmed at site B. Any calls made to non-working numbers on the 81 at site A get a VNR announcement(...you have reached a non-working number blah blah blah...) What I want to do is have a VNR for any calls to non-working extensions at site B. I don't have a MIRAN card, console or voicemail at site B. Is there a way to get the current VNR at site A to play for callers who call a non-working extension at site B? Right now callers hear the OVF at site B(fast busy).
 
Could you set VNR at site B to be routed over to site A for any non existing numbers?. i.e.

>LD 15
NET_DATA
OPT RTD
AC1 INTL NPA SPN NXX
AC2 LOC
FNP YES
ISDN YES
VPNI 0
PNI 1
PINX_DN
MBG 0
BSGC 65535
PFX1
PFX2
HLOC 524
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
TIDM NO
DASC
ROPT NRO
DITI YES
TRNX NO
EXTT NO
FTOP FRES
APAD 0 0
VNR YES ######################### Change to yes ######################

(Not sure of the next few prompts, but they refer to the digit length and tie line route used to site A)

NIT 8
NAS_ATCL YES
NAS_ACTV NO
FOPT 0
CNDN
CNAT
CNIP YES
CNTC
NATC
INTC


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Thanks firebird. Before I make that change, do i need to change anything in INT_DATA? Here's my current setup:

REQ: PRT
TYPE: INT
TYPE INT_DATA
CUST 0

TYPE INT_DATA
CUST 00
ACCD OVF OVF OVF ATN
CTVN OVF OVF OVF ATN
MBNR OVF OVF OVF ATN
CTRC OVF NAP OVF NAP
CLDN NAP OVF NAP NAP
NINV OVF OVF OVF ATN
NITR OVF OVF OVF ATN
NRES OVF OVF OVF ATN
NBLK OVF OVF OVF ATN
RCLE ATN OVF ATN ATN
CONG OVF
LLT OVF
DNDT BSY

REQ:
AUD000
 
For some customers, I tend to change CTVN OVF OVF OVF ATN to CTVN OVF OVF OVF OVF so that any DID / DDI calls to non existing extension numbers gives out the number obtainable tone. It also save bothering the operator and helps to prevent any dial through fraud by being routed to a mailbox that hasn't got a extension number etc.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Yes, we are using DSC from A to B and B to A.

 
If you do what firebird is talking about then you don't need cdp/dsc anymore. If the number doesn't live on site bs switch it's going back to site a
 
Yes as Rickpone has stated, it's a good feature to use and saves you having to go into ESN each time a user moves their number from one site to another.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top