Using the FAC to bypass AAR/ARS

[speechguy]

I have CM 2.0 on a CSI which is behind another switch.

I wanted to simply add a few analog ports to a trunk group on the CSI for dial out access.

Are there a few quick and easy steps to place calls using ther FAC?

Dial in works fine. But when I try to access (trk/grp1) I see COR issues.
I set the station cor to FRL-7, the trunk grp has FRL-1 (was 0).

You can see my test to FAC 171 fail. (But my test to TAC 170-Qsig seems fine)
LIST TRACE

time data

13:30:18 tone-receiver 01A0205 cid 0x180
13:30:18 active station 55555 cid 0x180
13:30:20 dial 171
13:30:20 denial event 1732: Caller COR Restricted D1=0x1 D2=0x180
13:30:20 dial 171
13:30:20 denial station 55555 cid 0x180
13:30:21 idle station 55555 cid 0x180
13:30:22 tone-receiver 01A0203 cid 0x181
13:30:22 active station 55555 cid 0x181
13:30:24 dial 170
13:30:24 busy trunk-group 2 cid 0x181
13:30:26 idle station 55555 cid 0x181
13:30:49 TRACE COMPLETE station 55555 cid 0x0

Anyone?

 

[speechguy]

Paul, orypecos,

Gentlemen, If I were to try using AAR, would I also be able to dial 3 digit extensions on the Ericsson?

Don

AT&T/Inter-Tel/Octel/Lucent/Avaya and now Adomo...does it get any better?? ;-)

 

[avayaman]

I don't see why not, as long as the strings were defined.

Paul Beddows

Consulting, Avaya/EAS implementation, Training
Vancouver, Canada
E-mail use form on website at

http://www.vancouver.hm/email.html

 

[avayaman]

Give me the number ranges in the erickson you wish to dial, plus the trunk group number in the Avaya & I will try & come up with something for you to try.

Paul Beddows

Consulting, Avaya/EAS implementation, Training
Vancouver, Canada
E-mail use form on website at

http://www.vancouver.hm/email.html

 

[speechguy]

Ok. Thanks Paul.

I'll dial the 200-299 range in the Ericsson using Trunk group 1

Don

AT&T/Inter-Tel/Octel/Lucent/Avaya and now Adomo...does it get any better?? ;-)

 

[speechguy]

I tried AAR like this but it did not work..

display aar analysis 1 Page 1 of 2
AAR DIGIT ANALYSIS TABLE
Percent Full: 7

Dialed Total Route Call Node ANI
String Min Max Pattern Type Num Reqd
171 3 3 1 aar n
2 7 7 254 aar n
3 7 7 254 aar n
4 7 7 254 aar n
5 7 7 254 aar n
6 7 7 254 aar n
7 7 7 254 aar n
8 7 7 254 aar n
9 7 7 254 aar n
9951000 7 7 2 aar n
n
n
n
n
n



-Don


AT&T/Inter-Tel/Octel/Lucent/Avaya and now Adomo...does it get any better?? ;-)

 

[speechguy]

I meant like this..and it did not work.

display aar analysis 2 Page 1 of 2
AAR DIGIT ANALYSIS TABLE
Percent Full: 7

Dialed Total Route Call Node ANI
String Min Max Pattern Type Num Reqd
2 7 7 254 aar n
2xx 3 3 1 aar n
3 7 7 254 aar n
4 7 7 254 aar n
5 7 7 254 aar n
6 7 7 254 aar n
7 7 7 254 aar n
8 7 7 254 aar n
9 7 7 254 aar n
9951000 7 7 2 aar n
n
n
n
n
n


AT&T/Inter-Tel/Octel/Lucent/Avaya and now Adomo...does it get any better?? ;-)

 

[avayaman]

What does the route pattern (254) look like. Don't you have to dial 9 to get out the the ericcson. If so you would only need an entry of 9 with min of 8 & max of 8.

Paul Beddows

Consulting, Avaya/EAS implementation, Training
Vancouver, Canada
E-mail use form on website at

http://www.vancouver.hm/email.html

 

[speechguy]

Paul,

Yes, I dial 9 for trunk access on the Ericsson.

Route 254 is empty.

I want to dial local 2xx extensions and then be able to dial 9,xxx-xxxx

Pretty basic huh?

thanks
Don



AT&T/Inter-Tel/Octel/Lucent/Avaya and now Adomo...does it get any better?? ;-)

 

[avayaman]

I would strip out all the aar entries there, add 2 new rotue patterns, add a single entry for 9 in the aar, send it to one of the new route patterns, delete it (1 under teh delete column) & then add it again followed by a pause if need. You really only need to do the delete & insert if the pause is required. Send 2 to another new route pattern for the 2XX locals. I think you really only new 2 entries in the AAR.


If that doesn't work, maybe use a wait for dial tone in the 2 route patterns (put a + in the inserted digits field)

Paul Beddows

Consulting, Avaya/EAS implementation, Training
Vancouver, Canada
E-mail use form on website at

http://www.vancouver.hm/email.html