USE one public line with two sites

[melhabba]

any one help me to solve this problem,

we have two sites with two Hipath4000 V5 ( distance between them 600 km) connected together by digital trunk ( TDCSU ) board ( DIUT2 ) and media ( fiber)

one of them ( SITE 1) has only one TMANI board and configure only one analogue public line ( configured with TACSU )

NOW ( SITE 1 ) can call ( SITE 2 ) WITH INTERNAL CALL )
SITE 1 can call external call by code CO ( 9 )

BUT ( SITE 2 ) can call SITE 1 with internal call but can not use public line that configured wIth SITE 1

how to change configure trunk in SITE 2 and SITE 1 TO allow use the public line ( that configured in SITE 1 )



THANK YOU

 

[Moriendi]

What you want is not difficult but there could be a number of reasons why it doesn't work. A TRACS trace from site 1 to show the message would be useful, as would the TDCSU,TACSU,COT,LDPLN,RICHT,LDAT config from site 1, may as well post a regen.

 

[donb01]

Seeing the config as requested will help. My first thought is that there is no route set up on site 2 to route external calls across the private link to site 1.

I have something similar set up for my remote sites. Each remote site has its own external trunking, but in case there is a problem with that I have a second route element set up so that if the first one fails (or all channels are busy) the call will then route to the main site and go out from there. I have the reverse set up for E911 because I have a central E911 system - all 911 calls are routed to the main site for processing, but if for some reason the link to the main site is down each site's 911 calls will go out its own local trunks. The dispatch center will get less information, but they will still have the address of the building the call came from.

So I'm guessing it's just a missing route.

Don Bruechert, Voice Comm Analyst II
CareTech Solutions @ Holy Family Memorial
Manitowoc, WI, USA

 

[melhabba]

good morning Moriendi and all

this is configuration in SITE 1 ( SITE 1 connected with external line ( public line )

<REGENERATE-TDCSU:;
REGENERATE-TDCSU:;
H500: AMO TDCSU STARTED
ADD-TDCSU:NEW ,1-01-025-0,4,4,0,0,200,1,1,"SIRTE ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",21,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-01-025-1,4,4,0,0,200,1,1,"GPTC-01 ",0
,ETSI,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",50,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,10,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-02-025-0,4,4,0,0,200,2,1,"SARIR ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",24,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-02-025-1,4,4,0,0,200,1,1,"GPTC-02 ",0
,ETSI,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",50,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,10,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-03-025-0,4,4,0,0,200,2,1,"TALHIA ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,1-1-100,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",25,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-03-025-1,4,4,0,0,200,2,1,"BENGHAZI ER ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,1-1-101,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",22,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-04-025-0,4,4,0,0,200,2,1,"AJDABYIA ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",23,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-04-025-1,4,4,0,0,200,2,1,"TAZIRBO ",0
,ETSI,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",26,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;
ADD-TDCSU:NEW ,1-04-079-210,200,99,0,0,99,1,1,"XPRESSIONS ",0
,ECMAV2,8,,NONE,,,,GDTR,N,TIE,NONE,N,0,
,,,,,
,31,MANY,,0,1,1,EMPTY,200,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",99,DSC,Y,SECURE,HG3550IP,
1&&20
,N,1,0,0,0,0,0,0,N
;

AMO-TDCSU-111 DIGITAL TRUNKS
REGENERATE COMPLETED;



<REGENERATE-TACSU:;
REGENERATE-TACSU:;
H500: AMO TACSU STARTED
ADD -TACSU: 1-1-115-5, , 2, 2, 0, 0,200, 1, 1,
,114, 0,"1-1-115-5 ",
0, 1-1-13, 2,1,EMPTY,0 ,
NONE, NONE, 1,EC &G711&G729AOPT,
" ", 0, GDTR,
0, ,Y ,TC ,TMANIMSG,
0, ,0,0, 1, 0, 1, 0,MOSIG-DTMF , 0-0 , 0,


AMO-TACSU-111 CONFIGURATION OF ANALOG TRUNK CIRCUITS IN THE SWU
REGENERATE COMPLETED;
<


<REGENERATE-COT:;
REGENERATE-COT:;
H500: AMO COT STARTED
ADD-COT: 1,RCL&ANS&CHRT&CEBC&FWDN&LWNC&NLCR&ICZO&
DFNN&DSDL&NOCI&NOCT&NTON;
CHANGE-COT:1,COTADD,,INDEP,
"S2GOROD";
ADD-COT: 2,RCL&XFER&ANS&DSIT&CEBC&FWDN&BSHT&KNDI&
ICZL&NTON;
CHANGE-COT:2,COTADD,,INDEP,
"TMANI";
ADD-COT: 3,RCL&XFER&AEOD&LWNC&NLCR&NTON;
CHANGE-COT:3,COTADD,,INDEP,
"E&M";
ADD-COT: 4,RCL&XFER&ANS&CEOC&CEBC&TIE&LWNC&NLCR&
ICZL&CCTN&DTNI;
ADD-COT: 99,XFER&ANS&CEOC&CEBC&FWDN&COTN&BSHT&FWDR&
BLOC&LWNC&ATRS&ROPT&TSCS&NLHT&NLRD&LINO&SNBE&
NCDR&LRPM&CTLS&CDN&CFBN&TWDS&DTNI;
ADD-COT: 100,XFER&ANS&KNEX&FWDR&DPRE&NTON;
ADD-COT: 200,ANS&CEBC&BSHT&BLOC&LWNC&NLCR&TSCS&DFNN&
NLRD&NOFT&NTON;

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
REGENERATE COMPLETED;


<REGENERATE-LDPLN:;
REGENERATE-LDPLN:;
H500: AMO LDPLN STARTED
ADD-LDPLN:LCRPATT,0,12-X,
0,
405

,,,
18,
,,,N;
AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN
REGENERATE COMPLETED;
<


<REGENERATE-RICHT:;
REGENERATE-RICHT:;
H500: AMO RICHT STARTED
ADD-RICHT:LRTENEW,405,ALL,"DIRECT LINE ",
405,405,,,
FIX,,"",PP300,,,,,YES,
NO,"",0,
NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO ;

AMO-RICHT-111 TRUNK ROUTING
REGENERATE COMPLETED;
<



<REGENERATE-LDAT:;
REGENERATE-LDAT:;
H500: AMO LDAT STARTED
ADD-LDAT:405,ALL,1,,405,405,1
,
,1,EMPTY,
WCHREG,
,4,,,,
,,,
,,,,,;

AMO-LDAT -111 LCR-DIRECTIONS
REGENERATE COMPLETED;
<

 

[Moriendi]

My crystal ball is not working today - which TDCSU from site 1 is the circuit to site 2?

You have no node numbers configured in the TDCSUs. That's probably bad. You also have a triple level node number in your TACSU, but a single level in your RICHT. That's also bad.

I assume from the LDPLN you posted, site 2 sends 12-X to site 1 ? And site 1 needs an LAUTH of 18 to dial it. Does that match with the transmitted LCOS or the LCOS of the TDCSU?

Are you able to make a tracs trace?

exe-tracs:bp;
res,all;
msglen,sw,g1,1000;
selmsg,sw,g1,all;
on,hd,"as:trace",99,y;

Now make the test call (do it fast before that file gets too big)
In tracs now type

off;
end;

Use Comwin-FT to remove that as:trace file and post it here.

 

[melhabba]

which TDCSU from site 1 is the circuit to site 2?
this is configured circuit in site 1 to connect site 2

ADD-TDCSU:NEW ,1-03-025-1,4,4,0,0,200,2,1,"BENGHAZI ER ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,1-1-101,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",22,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;

 

[melhabba]

good morning Moriendi

this is configured circuit in site 1 to connect site 2

ADD-TDCSU:NEW ,1-03-025-1,4,4,0,0,200,2,1,"BENGHAZI ER ",0
,CORNV33,1,,NONE,,,,GDTR,N,CO,NONE,N,0,
,,,,,
,31,MANY,1-1-101,2,1,1,EMPTY,4,1,N,
,,,,,16,8,1,10,,EC&G711&G729AOPT
,"",22,CIR,Y,TRADITIO,S2COD,
1&&30
,N,1,5,0,0,0,0,0
;

 

[Moriendi]

I thought you'd configured this and it wasn't working. Now I'm not sure if you've even configured it.

It would be easiest if you sent the regen of both sites and told me what they were dialling. Can you do that?

If you have configured it and it doesn't work - a trace as above is needed to see what is dialled.