Urgent:Dump problem

[cuneyt2919]

Hi
The system is BC12SP5 and 9 lims..
The problem occured after adding new lims..(2 lims were added)
[tt]
<dubdp;
BACKUP DATA
EXTERNAL BACKUP LATEST PREVIOUS
REL1 REL2
NOT VALID NOT VALID
LOCAL BACKUP
DIVERGENT TIME AND DATE LIM 1 FAULTY FAULTY
2 FAULTY FAULTY
3 FAULTY FAULTY
4 FAULTY FAULTY
5 FAULTY FAULTY
6 FAULTY FAULTY
7 FAULTY FAULTY
8 FAULTY FAULTY
9 FAULTY FAULTY



[/tt]
When we give dusyi command,

<DUSYI;
SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE

BUFFER TRANSFER ERROR 12:47 25OCT04
FAILED IN LIM008 AOM7

END

I give 2nd times the "DUSYI" command,
and this time it fails in AUM8

<DUSYI;
SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE

BUFFER TRANSFER ERROR 12:51 25OCT04
FAILED IN LIM008 AUM8


And here is what i did:
<rfpuI:UNIT=aom8,LIM=8;
RFPUI:UNIT=AOM8,LIM=8;
SURE? (YES/NO)
<y;

RESTART PROGRAM UNIT
LIM STARTED PU:S FAILED PU:S
8 AOM8

EXECUTED

<rfpuI:UNIT=aom7,LIM=8;
RFPUI:UNIT=AOM7,LIM=8;
SURE? (YES/NO)
<y;

RESTART PROGRAM UNIT
LIM STARTED PU:S FAILED PU:S
8 AOM7

EXECUTED

<rfpuI:UNIT=aum8,LIM=8;
RFPUI:UNIT=AUM8,LIM=8;
SURE? (YES/NO)
<y;

RESTART PROGRAM UNIT
LIM STARTED PU:S FAILED PU:S
8 AUM8

EXECUTED

<dusyi;
SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE
BUFFER TRANSFER ERROR 12:57 25OCT04
FAILED IN LIM008 AOM7

<rfpuI:UNIT=drdh,LIM=1;
RFPUI:UNIT=DRDH,LIM=1;
SURE? (YES/NO)
<y;

RESTART PROGRAM UNIT
LIM STARTED PU:S FAILED PU:S
1 DRDH

EXECUTED

<dusyi;
SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE

BUFFER TRANSFER ERROR 13:01 25OCT04
FAILED IN LIM008 AOM7

Does anybody help me about the issue?

Thank you very much for all your helps

 

[PetrNik]

Hello,
Just wait an hour with low traffic.
Or try SFCEI after RFPUI.
Or try DUSYIRINT=RESULT;

 

[antek]

Hi
1- First of all you must start to make PC generation immediately when finished Restart your input/output (NIU2 with flash Disk) RFBOI:BPOS=1-0-60;then logon again to your system .

2- Make DUBDP; then look if you have any backup in the flash disk or not if yes Make LADAI; your system will back to previous good status if you don’t have any backup

3- Make BLEQI: EQU= first I/O port (1-0-60-00)

4- Make FIMOE: SUBFS=SYSSUFS11;

5- Make FIMOE: SUBFS=SYSSUFS21;

6- Make FIFTI: SUBFS=SYSSUFS11;

7- Make FIFTI: SUBFS=SYSSUFS21;

8- Make FIMOI: SUBFS=SYSSUFS11;

9- Make FIMOI: SUBFS=SYSSUFS21;

10- DUSYI;

11- If you have any error at any previous step from 7 to 8 I think you must make initial load to your system from the beginning by (Ericsson Representative in you country).

BR

 

[cuneyt2919]

Unfortunately the same result..

<sfcei;
SFCEI;
SURE? (YES/NO)
<y;

START EXCHANGE
STARTED LIM:S FAILED LIM:S PARTLY FAILED LIM:S FAILED PU:S
1
2
3
4
5
6
7
8
9

EXECUTED


SPONTANEOUS PRINTOUT


IDENTITY: xxx
VERSION: CXP1010101/2/BC12SP5/R2A

DATE: 25OCT04 TIME: 14:59:36
CLASS: 0
260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGE
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
25OCT04 14:55:25 3 2 TLP11 007-1-72-07 76 91 1
RDATE RTIME
25OCT04 14:55:26
<dusyirint=result;
ORDERED

SPONTANEOUS PRINTOUT


IDENTITY: xxx
VERSION: CXP1010101/2/BC12SP5/R2A

DATE: 25OCT04 TIME: 14:59:37
CLASS: 0
260 FAULT ON LINE TO INTERWORKING PABX OR PUBLIC EXCHANGE
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
25OCT04 14:57:40 7 2 TLP11 007-1-72-03 76 95 1
RDATE RTIME
25OCT04 14:57:40
<;
SYNTAX ERROR
<dubdp;
NOT ACCEPTED
CONGESTION
<dubdp;
NOT ACCEPTED
CONGESTION
<dubdp;
NOT ACCEPTED
CONGESTION
NOT ACCEPTED
CONGESTION
SYNTAX ERROR
<hiEDP;
TIME DATE
15:00:36 25OCT04
LIM EVENTS OVERWRITTEN OLDEST EVENT NEWEST EVENT LAST HIREI
EVENTS
001 11 0 16:42:05 24OCT04 14:17:46 25OCT04 15:44:43 24OCT04
002 11 0 23:17:54 24OCT04 13:54:59 25OCT04 15:44:43 24OCT04
003 6 0 11:15:08 25OCT04 14:37:33 25OCT04 15:44:43 24OCT04
004 2 0 10:48:00 25OCT04 14:29:54 25OCT04 15:44:43 24OCT04
005 2 0 09:34:43 25OCT04 11:24:02 25OCT04 15:44:43 24OCT04
006 5 0 17:44:37 24OCT04 14:35:57 25OCT04 15:44:44 24OCT04
007 60 0 11:16:10 25OCT04 14:45:54 25OCT04 15:44:43 24OCT04
008 0 0 15:44:44 24OCT04
009 0 0 15:44:44 24OCT04

END
<;
SYNTAX ERROR
<;
SYNTAX ERROR
<;
SYNTAX ERROR
<;
SYNTAX ERROR
<;
SYNTAX ERROR

SPONTANEOUS PRINTOUT


IDENTITY: YKBDBLOK
VERSION: CXP1010101/2/BC12SP5/R2A

DATE: 25OCT04 TIME: 15:02:01
CLASS: 3
85 BUFFER TRANSFER HAS FAILED
DATE TIME ALP NOIF EQU INF1 INF2 INF3 INF4
25OCT04 15:01:15 14 1 008-0-**-** 301 6 8 9

<dubdp;
NOT ACCEPTED
CONGESTION

SPONTANEOUS PRINTOUT

SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE

BUFFER TRANSFER ERROR 15:01 25OCT04
FAILED IN LIM008 AOM7

 

[antek]

Hello again

I am sorry for my mistake


SUBFS=SYSSUFS xx is wrong the correct command is
SUBFS=SYSSUBFS XX

 

[cuneyt2919]

Ok thx antek, will try it and inform you about the result.

Rgrds.

 

[whosrdaddy]

cuneyt2919,

can you do following commands :

CNPIP:UNIT=AOM7;
CNPIP:UNIT=AUM8;

--------------------------------------
What You See Is What You Get

 

[cuneyt2919]

Hi all,
The problem is still same.. No change.Our vendor also had done the procedure before, about what antek said.

By the way, removing these program units, cause other program units fail during DUSYI process..My other topic was also related with this issue , "dusyi fails because of DMGM PU"

Any other idea what to do it so?


<CNPIP:UNIT=AuM8;

PROGRAM UNIT INFORMATION
PU-NAME PU-NO PRODUCT NUMBER REV PATCH
AUM8 H'2B2 7/CAA 111 8535/01 R2A NO
TYPE
B'0000 0000 0000 0000 0000 1000 0000 0010
TYPEEXT
B'0000 0000 0000 0000 0010 0001 0001 1010
LOADED IN LIM
8 9
ACTIVE CF LOCATED IN LIM 8

END
<CNPIP:UNIT=AOM7;

PROGRAM UNIT INFORMATION
PU-NAME PU-NO PRODUCT NUMBER REV PATCH
AOM7 H'29C 7/CAA 111 8522/01 R2A NO
TYPE
B'0000 0000 0000 0000 0000 1000 0000 0010
TYPEEXT
B'0000 0000 0000 0000 0010 0001 0000 1010
LOADED IN LIM
8 9
ACTIVE CF LOCATED IN LIM 8

 

[cuneyt2919]

Hi, Also now, i saw some alarms, like this..
"Buffer transfer hardware faulty" is related with this problem??

DATE: 27OCT04 TIME: 10:58:50
CLASS: 4
102 POWER FAILURE DETECTED BY DSU
DATE TIME ALP NOIF EQU INF1 INF2
26OCT04 12:20:08 1 1 007-0-**-** 2 4

CLASS: 2
15 DEVICE BOARD FAULTY OR MISSING
DATE TIME ALP NOIF EQU BRDID
26OCT04 12:21:29 2 1 007-2-62-00 69

CLASS: 1
62 BUFFER TRANSFER HARDWARE FAULTY
DATE TIME ALP NOIF EQU INF1
26OCT04 12:23:17 3 1 009-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 12:33:04 5 2 006-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 12:43:35 7 2 005-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 12:50:44 9 2 002-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 13:06:05 11 2 001-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 13:35:26 12 2 004-0-**-** 0

38 DISTURB. COUNTER INCREASED DUE TO FAULTY PROGRAM EXECUTION
DATE TIME ALP NOIF EQU INF1
26OCT04 15:37:48 13 2 003-0-**-** 0

 

[whosrdaddy]

do you have many lost signal comming from those lims??
hiedp:lim=8;
himdp:lim=8; (printsout lost signals)

look for MISMATCHING SEQUENCE NUMBER

--------------------------------------
What You See Is What You Get

 

[antek]

Hi Cuneyt.
1.For your dump problem I think you don’t have any
choices, you should be start to make initial
loading at any suitable time (by your Vender)


2. For alarm CODE 102
CLASS: 4
102 POWER FAILURE DETECTED BY DSU
DATE TIME ALP NOIF EQU INF1 INF2
26OCT04 12:20:08 1 1 007-0-**-** 2 4

You have problem with (ringing voltage) in
DSU at(lim7- Mag.3) so try to check or change
your Power cord at this MAG.

best regards

 

[cuneyt2919]

Hi
Unfortunately it was removed 10 minutes ago but no alarms stored after last hirei..
I think Ericsson support center, should connect remotely to switch...

<hiedp;
TIME DATE
16:03:31 27OCT04
LIM EVENTS OVERWRITTEN OLDEST EVENT NEWEST EVENT LAST HIREI
EVENTS
001 0 0 15:55:43 27OCT04
002 0 0 15:55:44 27OCT04
003 0 0 15:55:44 27OCT04
004 0 0 15:55:43 27OCT04
005 0 0 15:55:43 27OCT04
006 0 0 15:55:44 27OCT04
007 0 0 15:55:44 27OCT04
008 0 0 15:55:44 27OCT04
009 0 0 15:55:44 27OCT04
NO INFORMATION STORED

END

<allop;
ALARM LOG
IDENTITY: YKBDBLOK
VERSION: CXP1010101/2/BC12SP5/R2A

DATE: 27OCT04 TIME: 16:02:34
CLASS: 4
102 POWER FAILURE DETECTED BY DSU
DATE TIME ALP NOIF EQU INF1 INF2
27OCT04 15:55:43 1 1 007-0-**-** 2 4

CLASS: 3
85 BUFFER TRANSFER HAS FAILED
DATE TIME ALP NOIF EQU BRDID INF1 INF2 INF3 INF4
27OCT04 16:00:42 4 1 001-0-52-00 106 359 0 9 1

CLASS: 2
15 DEVICE BOARD FAULTY OR MISSING
DATE TIME ALP NOIF EQU BRDID
27OCT04 15:57:02 2 1 007-2-62-00 69

CLASS: 1
62 BUFFER TRANSFER HARDWARE FAULTY
DATE TIME ALP NOIF EQU INF1
27OCT04 15:58:14 3 1 009-0-**-** 0


LAST ALREI: 27OCT04, 15:55:41

 

[patcher]

Hello, initially you said the problem is after the last 2 lims are added. Well, the lims were added in a wrong way. If you add a lim, there should be no common function. This is because it will corrupt the data. It is more safe if you add the lim without any common function. My advice is to remove the last 2 lims and reconfigure it again properly.

 

[nanzaa]

Bonjour Excuse me Hello
For your problem dump try commands(orders) it following ones
/* FORMATAGE D'UN DISQUE MD110 */

/*

/*BLOCALE DU BUS SCSI */
bleqi:equ=1-0-60-0;

/*Invalide le REL1 */
fimoe:subfs=syssubfs11;

/*Invalide le REL2 */
fimoe:subfs=syssubfs21;


/*Invalide le disque */
iosie:node=sysn,iodev=sysdisk1;

/* a ce moment de la manip, on laisse le meme disque si on veut reformater le meme disque */
/* ou on en change pour faire une sauvagarde sur un autre disque */

/*LISTE LES PORTS DECLARES SUR LA NIU IPU */
ioddp;

I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU SIPOS TYPE/USAGE STATUS AUTH
SYSN - 001-0-60 - - IN SERVICE
SYSN SYSTERMINAL 001-0-60-1 - MML - 7
END

/*ASSOCIE UN NOM LOGIQUE D'UN PERIPHERIQUE AU BUS SCSI P148 */
iosii:node=sysn,iodev=sysdisk1,subfs=syssubfs11&syssubfs21,sipos=3;
/*associe un nom logique d'un periphereique aus ATA NIU2 */
iosii:node=sysn,iodev=sysdisk1,subfs=syssubfs11&syssubfs21,btype=ATA;
/* CREE UN NOUVEAU SYSTEM DE SOUS FICHIERS ET FORMATAGE DES RELS */
/* REL 1 */
ficri:subfs=syssubfs11,size=64;
/* REL 1 NIU2 CF256 */
ficri:subfs=syssubfs11,size=100;
/*REL 2 */
ficri:subfs=syssubfs21,size=64;
/* REL 2 NIU2 CF256 */
ficri:subfs=syssubfs21,size=100;
/*MONTAGE D'UN SYSTEME DE SOUS-FICHIERS POUR LE REL1 (P128) */
fimoi:subfs=syssubfs11;


/* IDEM POUR LE REL2 */
fimoi:subfs=syssubfs21;

/* LISTER LES PORTS */
ioddp;

I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU SIPOS TYPE/USAGE STATUS AUTH
SYSN - 001-0-60 - - IN SERVICE
SYSN SYSDISK1 001-0-60-0 3 ADTX MAN BLOCK
SYSSUBFS11
SYSSUBFS21
SYSN SYSTERMINAL 001-0-60-1 - MML - 7
END


/* LISTAGE DES FICHIERS IPA CHARGER DANS LE MD110 */
ficapath=/sysn/usr1/ses/li;
CATEGORY INFORMATION
FITYPE OWNER-ACC GROUP-ACC OTHER-ACC FILE
D R W X R W X R W X LI
F R W - R W - R W - 02-0421-1.LIC
F R W - R W - R W - 40-0421-1.LIC




/* DEBLOQUE LE BUS SCSI */
bleqe:equ=1-0-60-0,allfm=yes;

/*LANCE UNE SAUVEGARRDE */
dusyirint=all;


WAIT FOR CHECK READING OF RELOAD DIRECTORY
CHECK READING SUCCESSFUL
BACKUP DATE INFORMATION FILE DUMPED
DUMP TO EXTERNAL BACKUP FINISHED
LOAD OF STANDBY SIDE HAS BEEN ORDERED
COPYING OF RELOAD DIRECTORY HAS BEEN ORDERED

/* EDITE LE FICHIER REL1 */
<fiofp:node=sysn;
OPEN FILE DATA FOR USERS
USER FILE
DR /USR1/SES/DR/REL1
END

 

[whosrdaddy]

hi nanzaa,

reformatting the disk will not help in this case. if you read the thread you will see they already tried that...

--------------------------------------
What You See Is What You Get

 

[cuneyt2919]

Hi nanzaa,
whosrdady est exact. Nous l'avons essayé la semaine dernière

désolé pour mon mauvais Français

 

[PhoneHacker]

excuse my english

Check the size of file system

1 - 10 = 60 Mb flash 128
11 - 30 = 120 Mb flash 256
31 - 124 = 192 Mb HDU7/1

9 lim = 60 Mb

view actual size
FISCP:IODEV=SYSDISK1;

do not function:
check disk or change
test 9 lim = 120 Mb

 

[cuneyt2919]

Hi,
This is the result for fiscp

<FISCP:IODEV=SYSDISK1;
FILE SYSTEM CAPACITY DATA
TOTAL DISK SPACE: 122 MBYTES
SUBFS: SYSSUBFS11
KBYTES FILES
TOTAL AVAIL TOTAL MOUNTED
40960 39728 10000 /SYSN/USR1
SUBFS: SYSSUBFS21
KBYTES FILES
TOTAL AVAIL TOTAL MOUNTED
40960 40612 10000 /SYSN/USR2
END

So Is there anything wrong with it?
Rgrds.

 

[rfpui]

Hi cuney
Your subfs file have now 40MB size and PhoneHacker have right that subfs should be 60 (64) Mb.
You have empty flash without data. Then try to change size
FICRI:SIZE=60,SUBFS=SYSSUBFS11;
FICRI:SIZE=60,SUBFS=SYSSUBFS21;

 

[patcher]

What is wrong with you guys!!! The original problem is not a backup problem. Not sure but someone add the LIMs with out any knowledge. 1st rule, no common functions on the added LIM. If you will check the LIM disp for LIM X you cannot see any common function. That is why Ericsson recommend to add LIM after 11 LIM. But you can add if you just remove the common functions. I hope everything is clear.