Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Upgrade rls 4.5 to Rls 5 Problem

Status
Not open for further replies.

scs5000

Vendor
May 4, 2008
23
Hi all i upgraded a release 4.5,11c,SSC to release 5. There were some digital ISM, PCA and 2 packages upgraded, Upgrade was successful and keycode validation was also successful but after rebooting and few minutes i got error message " Security device not found or missing or security device have been moved" these type of message i get. I cold/softboot PBX with no success, I then reinstalled release 5 from scratch, i mean from PCMCIA, this time installation and keycode validation was also successful but after few minutes i get same error, when i revert back to release 4.5 it works OK. I don't know what am i doing wrong, The SSC Eng code is NTDK20JA and software daughter board release is NTSK01ADE5. In Keycode sheet the feature package is NTSK01GD.Can i use both these hardware with Release 5?? If yes then what i am doing wrong??
Regards
 
Is this a TDM only switch ? I know all the IPMG Release 5's I have done came with a new Security dongle. Not sure if the TDM only should have came with a new one.
 
Yes this is a TDM, i mean all analog and DLC cards with PRI`s.
 
I think you need to use a new dongle,its the dongle for a big switch because in theory you are big switch now
 
You don't need a new dongle, but have you checked the original dongle is fitted to the SSC card. With Rls 5 if you do a TDM only upgrade you keep the SSC card with its small system dongle, if you have any IP, even 1 IP license then the SSC card will be replaced by a CPPM card with a Large System Dongle and a number of MGC cards.
 
The dongle is fitted already. Any more help
regards
 
I have seen this on some upgrades. Remove the dongle and wope both sides and reinsert. do not touch the flat sides with your fingers.

Another thing it could be is the AUX id check to make sure they match what is on the dongle.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
scs5000...from what it sound like to me you have not
converted your database.have you done all of the procedure.

no problems only solutions

strmwalker
 
scs5000..looking at the procedure you should be using
either nttk13 or nttk25 software daughterboard

no problems only solutions

strmwalker
 
did you download the keycodes from the nortel website? if so check to make sure that the sys id matches.. i've seen nothing more then just a bad batch of keycodes cause simular problems.. some moves to 5 do require a new dongle, others do not.. it depends on ip lic and the way the keycodes were generated BUT the eng website at nortel should include that information

john poole
bellsouth business
columbia,sc
 
I reinstalled OS from scratch also with no database and it still gave same error,Tried cleaning Dongle also.
Yes i downloaded Keycode from Website and also got Blue keycode sheet from Nortel and System Id`s are same.
I am not sure about Daughter board NTTK13/25. I dont have these D/Boards. Still struggling to find out what would be the solution.
One more thing that when i got the Keycode Box it has also a Nortel package sheet outside box in which package details were mention, on this paper a keycode sheet and a security device was mentioned but inside Box i couldn't found any security device.
I am still not sure whether i need anew dongle for converting CS100M cabinet Release 4.5 to CS1000M cabinet Release 5.

Regards
 
open a ticket with Nortel at this point, sounds like you've tried everything else!
 
This was a problem in 4.5. Nortel has to write a patch for this issue. If the keycodes validated then it is not the AUX ID. I would contact Nortel and have them write a patch.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top