Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Unable to upgrade LDK300

Status
Not open for further replies.

Jonno6503

Programmer
Aug 3, 2006
22
GB
Hi All

Ive tried to upgrade a LDK300 both via serial and tcp/ip both seem to get to 99 retrys and then fails.
any ideas

current firmware is
UK-80P-B.0Cj Dec02

trying to update using bin
82P-30Ds

 
Please check your firmware again with [Trans/Pgm + 72].
If you are using UK-80P-B.0Cj Dec02 this does not sound like LDK-300.
It should be XX-30P-xx.xx xxxyy.
And your hardaware is maybe not compatible with the new s/w.
82 sounds to me to be a hotel s/w.

Your current version is 2.0 (B.0 Cj)

Check the name of the processorboard (MBU) and post the name and version here. Also daughter boards (piggy back).



///doktor
____________________________________
 
Hi

80p is LDK300 Hotel.

Cant find software on 82p. Can you double check its definitely 82p your trying to upload? What are do you think your upgrading from and to? Your currently on hotel version 2 for LDK300. Are you trying to upgrade to the latest version or changing it to office software? Or are you swapping the MPB for the LDK300E?

Eats

Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!
 
Yes. You need to state what MPB and ASMU/PMU you have installed.
I guess that your problems relate to lack of hardware compability.

///doktor
____________________________________
 
ah yes dont know exact mpb type nothing been changed since original install circa 2002
 
main board just says LDK-300 MPB
it has a pmu,modu and sdmu32 and thats it




 
Ok

First ping the system as earlier systems didnt have the ip address in as default. Then log onto the system using the ldk admin 2.2 tool and once connected, disconnect then use the upgrade tool to upgrade to 80p 3.6 only. Dont go above 3.6 as the mpb will not take 3.7 above. I did an office one 2 weeks ago on 2.0 and couldnt upgrade so used admin tool 2.2 and it worked. Also had to swap the smdu32 card as it was faulty.

Good Luck

Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!
 
Cool will try later admin

this the version im using tho :

LDK PC Admin Ver B.2Fe
 
Have now installed Admin Ver 2.0Ba or have i just gone backwards ?
 
If the system has no password set, set a password and retry the upgrade. Ive found some software versions very particular about firmware and database UP/Down with no password set.
 
Password isnt the problem
it just fails

i am now suspicious of the firmware im trying to use now
as the other site i know has the same system is running 80p-30Ds
and i dont have that version or 3.6 either

Does anyone know where i can download it ?
 
Fyi
below is the monitor transcript

===============================
Upgrade monitor ver 1.0
===============================
Creating Thread.
Creating Thread...Success
Connecting to system.
.(Checksum : 87 9e)IP : 10.0.0.10
Connecting to system...Success
Negotiating.
.-.* OnePacket-Received[4]: 02 10 10 03
Nego_start was received
WriteData[9]: 02 10 18 04 35 35 36 36 03
..Password is being confirmed.-.* OnePacket-Received[4]: 02 10 19 03
: Password was confirmed
WriteData[6]: 02 10 11 01 11 03
..Upgrade Service is being requested.-.* OnePacket-Received[6]: 02 10 12 01 11 03
: Upgrade Service was confirmed
WriteData[4]: 02 10 14 03
..Version is being requested.-.* OnePacket-Received[16]: 02 10 15 0b 55 4b 38 30 50 2d 42 2e 30 43 6a 03
: Got version [UK80P-B.0Cj]
WriteData[6]: 02 10 16 01 11 03
.Start was requested.-.* OnePacket-Received[6]: 02 10 17 01 11 03
: Ready to start
WriteData[8]: 02 11 10 03 10 00 00 03
.Checking Boot ROM Checksum.-.* OnePacket-Received[6]: 02 11 11 01 10 03
: Boot ROM confirmed
Negotiating...Success
Sending data.
SocketThread_SendData is executed.
START OF ZMODEM SENDING
.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-

Socket Closed...
WSAECONNABORTED
WaitCount in readline() is 99
Error Code is -3
Sending data...Fail
Disconnecting.
OnSocketClose
Disconnecting...Success
Erase upgrading process.
Erase upgrading process...Success
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top