Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Unable to invoke software installation

Status
Not open for further replies.
LittleMaster

LittleMaster

Technical User
Sep 16, 2015
182
PK
Greetings,
I want to install software on cs1k rls 450w


Kindly help...what can be the issue.
Thanks
 
Sort by date Sort by votes
First of all you can't use a 1 gig PCMCIA card.
Up to a 128 Meg card is only accepted and the manufacturer should be SanDisk where possible.

For SSC processor cards, I think NTSK20AB is too old. You will need a newer SSC card. I recall that NTSK20HA was the minimum version that was compatible for use with release 04.50.

What size RAM do you have as I think you need a single 16 Meg rather than the original 8 Meg card on the SSC.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
Thanks for our reply,
I have 128MB card, programmed with cardpro9. Copied extracted files of software 4.5 ap-emea_450w_r20 to flash card. My SSC card is ntdk20ja, software daughter board is ntsk40as , 17. Inserted the pcmcia in slot A, reboot the system , pressed control_I but I got these messages ,,images are attached ..what can be the issue plz...
 
Upvote 0 Downvote
What is the manufacturer of your pcmcia/Compact Flash card?. I've had on many occasions found that some types aren't compatible or that they weren't formatted correctly using the card programmer tool.

What you can do is to format the card on an very old Windows operating system such as Windows 98 / 95 etc or from any non Windows computer such as Linux etc.

As the card is 128 Megs, then just copy the single *.exe file onto the card and run the extraction from it as there will be plenty of space.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
SanDisk obtained,
Software started successfully,,but keycode not validating..is there any issue with FEATURE SRT SELECTION according to ntsk40ac card..because the options does not shown for ntsk40ac in software package which I am installing.. I think I will need rls 4.5 software for ntsk40ac
 
Upvote 0 Downvote
Firebird do you have rls 4.5 software for ASIAPAC ntsk40ac or ntsk40ab ?
 
Upvote 0 Downvote
Yes I have all the software releases. Just follow my link.

Due to browser security changes, you might need to edit the link and use an FTP client such as Filezilla ftp client to access the files.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
Thanks Firebird, I have checked the ftp link. There are 2 copies available for small system software release 450w, but unfortunately the Feature set for NTSK40AC and NTSK40AB is not available in the package.
 
Upvote 0 Downvote
There were only two versions released. Are you certain that it's release 04.50w ?. Did you have a Nortel sheet?

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
Thanks for your reply,
Here is a screenshot from technical bulletin..
Screenshot_20231207-013923_Drive_lthwbh.jpg
 
Upvote 0 Downvote
Yes, I have tried it's all Feature sets but at the end facing issue keycode INVALIDATION, even I am having the keycodes with requisite available dongle
 
Upvote 0 Downvote
Is the system currently in use?

If so, then you can go into LD 143 from TTY 0 and key in UPGRADE

Go into the installation summary and print off the details

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
A screenshot from a capture when it was in working condition which software should I install to solve the keycodes issue..should I match and enter all pkg and license information for the keycodes Validation?

20231207_113615_wahumk.jpg
 
Upvote 0 Downvote
Have you got the official Nortel keycode sheet?.

If you haven't, then I'm guessing that you are only referring to screen shots from when it was working?. If so, then you will need a fair bit of details such as packages used and any AUX ID etc.

The details for the packages were already explained in LD 143 under UPGRADE.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
Thanks Firebird..everything has done OK..The software is installed...
Just changed selection of FEATURE SET during software installation..

Thanks
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

LittleMaster
  • Locked
  • Question
Software needed for cs1k ls 45 FEATURE SET 1
Replies
1
Views
132
Firebird Scrambler
Firebird Scrambler
JM2009
  • Question
CS1000 how to use telent to download the ip trunk error message??
Replies
3
Views
303
psychotech
psychotech
Trason
  • Locked
  • Question
e911 on rls 7 where to start
Replies
2
Views
383
bignose21
bignose21
VRRyan
  • Locked
  • Question
Finding password to CS1000 5.5 SSC
Replies
2
Views
351
Firebird Scrambler
Firebird Scrambler
lastation4
  • Locked
  • Question
Can't get T1 DCH to establish
Replies
6
Views
273
lastation4
lastation4

Part and Inventory Search

Sponsor

Back
Top