Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
UDP Software
- Thread starter b9dvator
- Start date
kwing112000
Vendor
it is not really called UDP in the IPO but you can use short codes to get the same thing working.
Kevin Wing
ACA- Implement IP Office
Carousel Industries
Kevin Wing
ACA- Implement IP Office
Carousel Industries
- Thread starter
- #3
kwing112000
Vendor
Can you give me a little more detail into what you are looking for? You can use short codes in each user.
Kevin Wing
ACA- Implement IP Office
Carousel Industries
Kevin Wing
ACA- Implement IP Office
Carousel Industries
- Thread starter
- #5
hello Kevin
Again thank you for your assistance.
What i have are non consecutive DID's, some of which i want to direct over a line side PRI w/QSIG enabled, to another PBX (non Avaya), ,
With the G3, i can leverage the UDP table (UDP routing first)to send the inbound call to an AAR table which directs it that specific trunk group supporting the other switch, , ,
Can i do the same with the short codes, obviously i'm out my element here with the IPO 412
Many thanks again for your assistance
b9dvator
Again thank you for your assistance.
What i have are non consecutive DID's, some of which i want to direct over a line side PRI w/QSIG enabled, to another PBX (non Avaya), ,
With the G3, i can leverage the UDP table (UDP routing first)to send the inbound call to an AAR table which directs it that specific trunk group supporting the other switch, , ,
Can i do the same with the short codes, obviously i'm out my element here with the IPO 412
Many thanks again for your assistance
b9dvator
Go to your incoming call route
If your DDI is already configured there then give it the destination you want
If internal then select the user or group
If external then enter the prefix and the number
That easy it is
If your incoming call route is not defined yet then make a new one
Select the incoming line id the trunk uses (default 0)
Then insert the DDI and give it a destination
ACA - Implement IP Office
ACS - Implement IP Office
ACA - Implement IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
If your DDI is already configured there then give it the destination you want
If internal then select the user or group
If external then enter the prefix and the number
That easy it is
If your incoming call route is not defined yet then make a new one
Select the incoming line id the trunk uses (default 0)
Then insert the DDI and give it a destination
ACA - Implement IP Office
ACS - Implement IP Office
ACA - Implement IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
kwing112000
Vendor
Peter is correct. there are a few ways to get this done. What i may do is use system short codes. make the system short codes like this. say 3322 was the DID and you want to route to another PBX.
S/C 3322
Dial
T/N 3322
Line of your QSIG or trunk to other system.
Then you will need an incoming call route
Line 0(or what ever your DID's come in on.)
incoming digits 3322
Destination 3322.
Thats the basic idea. You can also do ranges using xx's and stuff.
Kevin Wing
ACA- Implement IP Office
Carousel Industries
S/C 3322
Dial
T/N 3322
Line of your QSIG or trunk to other system.
Then you will need an incoming call route
Line 0(or what ever your DID's come in on.)
incoming digits 3322
Destination 3322.
Thats the basic idea. You can also do ranges using xx's and stuff.
Kevin Wing
ACA- Implement IP Office
Carousel Industries
- Status