I am trying to upgrade a UCM module from R10 to R11. I upload the iso through web manager solutions setting, i choose upgrade and it appears to go through the upgrade normal. i even get a message saying its been upgraded with no errors. However, the UCM reboots and when it comes back on it shows R1 as the version with R11 as the available upgrade. Why does it appear the upgrade is completing and upon reboot its back at R10?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
UCM R10 to R11 2
- Thread starter gknight1
- Start date
- Thread starter
- #2
Sorry, I see the mention of R11.1 in your second post. You need to upgrade the UCM to 11.0.4.3 first and then follow the special process. It may be better to wait for 11.0.4.4 which is imminent but also has an improved upgrade process.
Having been working on UCMs all last week, if you'r looking at the status in SSA, following an upgrade some of the version info shown doesn't update until you force screen refresh by doing something like clearing alarms and then coming back to the SSA screen.
Stuck in a never ending cycle of file copying.
Having been working on UCMs all last week, if you'r looking at the status in SSA, following an upgrade some of the version info shown doesn't update until you force screen refresh by doing something like clearing alarms and then coming back to the SSA screen.
Stuck in a never ending cycle of file copying.
- Thread starter
- #5
Read the technical bulletin for 11.1, a link for it is on the same page as the 11.1 software on support.avaya.com. It explains that you need to upgrade to 11.0.4.3 before upgrading to 11.1 and has a link for the document for upgrading to 11.1.
Stuck in a never ending cycle of file copying.
Stuck in a never ending cycle of file copying.
- Thread starter
- #7
i did read it, but's not very clear. i'm going to try to go to r10.1 first jsut to see if i can.
also, the system always seems to get hung up on Transferring at 90%. It doesn't matter what version i try to transfer, it also hangs at 90%. When looking at SSA it still shows i have 10GB free and the free disk counter doesnt go down, so I shut it down and restart it and it shows an upgrade is available.
also, the system always seems to get hung up on Transferring at 90%. It doesn't matter what version i try to transfer, it also hangs at 90%. When looking at SSA it still shows i have 10GB free and the free disk counter doesnt go down, so I shut it down and restart it and it shows an upgrade is available.
- Thread starter
- #8
- Thread starter
- #9
- Thread starter
- #10
Try going into the module's web control menus on 7071 and in the Upgrades menu run Clear Local Cache a few times. Then try ISO transfer again.
If ISO transfer still isn't working then fallback to USB upgrade key. If the module is remote but you have SSA access, mail the key to someone trusted and then run the process remotely.
Stuck in a never ending cycle of file copying.
If ISO transfer still isn't working then fallback to USB upgrade key. If the module is remote but you have SSA access, mail the key to someone trusted and then run the process remotely.
Stuck in a never ending cycle of file copying.
-
1
- #12
I've done it with USB upgrade. But like Sizbut says you need to go to 11.0.4.3 first before 11.1 there are centos options that need to be installed before going 11.1. Done two now with usb and both have been successful. If you still have issues with the Web would suggest you use the usb.
- Thread starter
- #13
well, we ended up on R11.0.4.3 via the USB fresh install and will just leave it there.
Now i have saved the vmpro database file, the acount folders, grettings, etc. How can i upload these? i tried using winscp, but am getting the persmisions error? i tried to do the chmod via putty, but it doesnt seem to exist. any guidance would be appreciated.
Now i have saved the vmpro database file, the acount folders, grettings, etc. How can i upload these? i tried using winscp, but am getting the persmisions error? i tried to do the chmod via putty, but it doesnt seem to exist. any guidance would be appreciated.
-
1
- #14
you have to enable the Administrator account to be in the wheel group.
Joe
FHandw, ACSS (SME)
Remembering intrigrant 2019
Joe
FHandw, ACSS (SME)
Remembering intrigrant 2019
- Status
Similar threads
- Locked
- Question
- Locked
- Question