Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Two Carriers, CS1K Only Passes One to 2nd PBX

Status
Not open for further replies.
ComradeSlice

ComradeSlice

IS-IT--Management
Feb 27, 2018
20
US
I have a CS1000 with three T1's: a DID PRI (NI2) from our local carrier, a TIE E&M from our long distance carrier, and a TIE PRI (QSIG/ISGF) that goes to an Asterisk PBX. I use DSC's to route extensions (4-digit) to the Asterisk TIE. Asterisk can make outgoing calls over the local and long distance trunks however incoming calls only go to Asterisk from the local trunk. Incoming calls from the long distance trunk to Asterisk get a fast busy. I see nothing on the Asterisk DCH when a call comes over the long distance trunk so I'm assuming the call is getting dropped because of the Meridian. Calls going from the long distance trunk to a Meridian extension complete successfully. What could be causing this? Here is some info.

Thanks in advance!

Local:
Code: 
DES  LIGHTPATH
TN   006 01
TYPE DID
CDEN SD
CUST 0
TRK  PRI
PDCA 1
PCML MU
NCOS 0
RTMB 6 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST  NO
IAPG 0
CLS  UNR DTN CND WTA LPR APN THFD HKD
     P10 VNL
TKID
DATE 27 JUN 2014

Long Distance:
Code: 
DES
TN   009 01
TYPE TIE
CDEN SD
CUST 0
TRK  DTI
PDCA 1
PCML MU
NCOS 0
RTMB 4 1
TGAR 0
SIGL EAM
STRI/STRO WNK WNK
SUPN YES
AST  NO
IAPG 0
CLS  UNR DTN CND WTA LPR APN THFD HKD
     P10 VNL
TKID
DATE 15 JUL 2013

Asterisk:
Code: 
DES  ASTERISK
TN   007 01
TYPE TIE
CDEN SD
CUST 0
TRK  PRI
PDCA 1
PCML MU
NCOS 0
RTMB 7 1
B-CHANNEL SIGNALING
TGAR 1
AST  NO
IAPG 0
CLS  UNR DTN CND WTA LPR APN THFD HKD
     P10 VNL
TKID
DATE 16 FEB 2018
 
Sort by date Sort by votes
Here they are:

Code: 
DSC  2700
FLEN 4
DSP  LSC
RLI  6
NPA
NXX
DSC  2761
FLEN 4
DSP  LSC
RLI  6
NPA
NXX
DSC  4349
FLEN 4
DSP  LSC
RLI  6
NPA
NXX
 
Upvote 0 Downvote
Here is the RLB, route, and DCH.

RLB:
Code: 
RLI  6
ENTR 0
LTER NO
ROUT 7
TOD  0 ON  1 ON  2 ON  3 ON
     4 ON  5 ON  6 ON  7 ON
CNV  NO
EXP  NO
FRL  0
DMI  0
FCI  0
FSNI 0
SBOC NRR
OHQ  NO
CBQ  NO

ISET 0
NALT 5
MFRL 0
OVLL 0

Route:
Code: 
TYPE RDB
CUST 00
DMOD
ROUT 7
DES  ASTERISK
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
    MODE PRA
    IFC  ISGF
    SBN  NO
    PNI  00000
    NCNA NO
    NCRD NO
    CHTY BCH
    CTYP UKWN
    INAC NO
    ISAR NO
    CPFXS YES
    DAPC NO
    INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8907
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC  NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
     OGF 512
     EOD 13952
     NRD 10112
     DDL 70
     ODT 4096
     RGV 640
     GRD 896
     SFB 3
     NBS 2048
     NBL 4096
     TFD 0
DRNG NO
CDR  NO
MUS  NO
EQAR NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

DCH:
Code: 
ADAN     DCH 7
  CTYP MSDL
  CARD 07
  PORT 1
  DES  asterisk
  USR  PRI
  DCHL 7
  OTBF 32
  PARM RS422  DTE
  DRAT 64KC
  CLOK EXT
  IFC  ISGF
    PINX_CUST 0
    ISDN_MCNT 300
  CLID OPT0
  CO_TYPE  STD
  SIDE NET
  CNEG 1
  RLS  ID  **
  RCAP COLP NDI CCBI CCNI PRI DV3I MQC CTI
  PR_TRIGS DIV 2 3
           CNG 2 3
  PR_RTN NO
  MQC_FEAT
  MBGA NO
  OVLR NO
  OVLS NO
  T310 120
  T200 3
  T203 10
  N200 3
  N201 260
  K    7
 
Upvote 0 Downvote
Has you checked that NCOS and FRL has sufficients rights to pass a route?
 
Upvote 0 Downvote
Remove that TARG entry from the route by doing X1
 
Upvote 0 Downvote
I removed the TARG. My NCOS levels 0 through 7 are 1 to 1 for FRL. I know how NCOS applies to stations but I do not know too much about how it applies to routes. What should I check? The issue I am having only applies when a call is going from my long distance (loop 9 route 4) to Asterisk (loop 7 route 7).

This is my FCR:
Code: 
CRNO  0
INIT DENY
ALOW 911
     958

CRNO  1
INIT ALOW
DENY 1
     411
     540
     555
     550
     976
     0

CRNO  2

CRNO  3

CRNO  4

CRNO  5
INIT ALOW
DENY 1900

CRNO  6

CRNO  7

CRNO  8

CRNO  9
 
Upvote 0 Downvote
Have you been administrator for this switch a while? Do you know if you guys use tenant service or have tbar set up? Both could affect trunk to trunk connections. What about TRNX and EXTT in NET_DATA. I've seen those settings cause issues with trunk to trunk connections. Even if the local call passes I would still check. The LD trunk is making the call so the NCOS could be an issue but I see the FRL for the RLI is 0 and that is what the trunk has. If it was a signaling issue seems like you would see something with dchannel monitoring.
And what calls are inbound on the LD T?
 
Upvote 0 Downvote
I have administered this system for a few years but we've never had to do trunk to trunk transfers before. We built Loop 7 for Asterisk a few weeks ago. TRNX and EXTT are both set to NO. I set them both to YES but that does not appear to have helped. Loop 9 (DTI) is our long distance trunk. The only incoming calls on that trunk are from our corporate office (AT&T set this up, it supposedly saves money). All other incoming calls go over Loop 6 (PRI). I am confused as to why incoming calls from Loop 6 successfully transfer to Loop 7 but incoming calls from Loop 9 do not. I see nothing on the dch when a call comes in from Loop 9 to an extension in Asterisk.
 
Upvote 0 Downvote
How are the incoming calls arriving? Are they the exact dns as built in CDP or are they sending 7 or 10 digits? If they aren't the dns you have defined you will need an IDC table or change the dsc to match. Sounds like the switch isn't even attempting to signal the DCH.
 
Upvote 0 Downvote
The trunks send the last 4 digits and the DNs are defined accordingly. You are correct the DCH is silent when a call comes in over Loop 9. Only calls to Meridian DNs over Loop 9 are routed properly. Calls do come in over Loop 6 to Loop 7. Meridian sets are also able to dial DSC extensions that go to Loop 7. Asterisk is able to grab Loop 6 and Loop 9 via their ACODs to make outgoing calls. The only thing that does not work properly is incoming calls from Loop 9 to Loop 7.
 
Upvote 0 Downvote
Our vendor just changed Loop 9 from TIE to DID. Now instead of a fast busy to Asterisk DNs we get our attendant, which is what happens when someone dials a DID that's not programmed in the Meridian.

Code: 
TYPE RDB
CUST 00
DMOD
ROUT 4
DES  ATT
TKTP DID
NPID_TBL_NUM   0
SAT  NO
RCLS EXT
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL 3VCE
PTYP DCO
AUTO NO
DNIS YES
NDGT 31
WDGT L
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7094
CPP  NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC  YES
DCNO 0
NDNO 0 *
DNAM NO
TIMR ICF 512
     OGF 512
     EOD 13952
     DSI 34944
     NRD 10112
     DDL 70
     ODT 4096
     RGV 640
     FLH 510
     GRD 896
     SFB 3
     TFD 0
SST  5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR  NO
MUS  YES
MRT  1
MR   NO
MANO NO
EQAR NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART  0
SGRP 0
AACR NO
 
Upvote 0 Downvote
I see a whole lot wrong with that RDB or things that look odd

Why is DNIS YES

Why is IDC YES

The NEDC and FEDC should be eth eth
 
Upvote 0 Downvote
I don't think they are sending 4. These numbers are internal only or are they DID? If the are DID I would go ahead and build an IDC for the whole ten and seven digit number xlating to the DSC. Assign that to route and see if it helps. I never trust ATT.
 
Upvote 0 Downvote
what do the inbound dch messages show when trying to contact one of these numbers? if the local works capture that & compare it with the inbound long distance DCH trace, also if these are trunk to trunk shouldn't the CDP type be TSC & not LSC?

Remember if it doesn't work hit it harder

Scott UK
 
Upvote 0 Downvote
also just wondering, what is the route Class of your inbound local & long distance routes

Remember if it doesn't work hit it harder

Scott UK
 
Upvote 0 Downvote
When I put an extension on TSC instead of DSC I was unable to call it via local trunk.

Here are the classes on the local trunk:
UNR DTN CND WTA LPR APN THFD HKD
P10 VNL

Here are the classes on the long distance trunk:
UNR DTN CND ECD WTA LPR APN THFD HKD
P10 VNL

Here are the classes on the Asterisk trunk:
UNR DTN CND WTA LPR APN THFD HKD
P10 VNL

I cannot do DCH trace on Loop 9 (long distance) because it is a DTI. Loop 6 (local) inbound loops like this:

Code: 
DCH 7 UIPE_OMSG CC_SETUP_REQ  REF 0000010A CH 7 23 TOD   9:16:42
CALLING #:6315592559 NUM PLAN: UNKNOWN   TON: UNKNOWN
CALLED  #:2700 NUM PLAN: PRIVATE   TON: ESN CDP

DCH 7 UIPE_IMSG CC_PROCEED_IND  REF 0000010A CH 7 23 TOD   9:16:42

DCH 7 UIPE_IMSG CC_ALERT_IND  REF 0000010A CH 7 23 TOD   9:16:42
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 7 UIPE_IMSG CC_SETUP_CONF   REF 0000010A CH 7 23 TOD   9:16:46
PROGRESS: TERMINATING END IS NOT ISDN
CONNECT #:2700 NUM PLAN: NONE  TON: UNKNOWN

DCH 7 UIPE_IMSG CC_DISC_IND   REF 0000010A CH 7 23 TOD   9:16:48
CAUSE: #16 - NORMAL CALL CLEARING

DCH 7 UIPE_OMSG CC_RELEASE_REQ  REF 0000010A CH 7 23 TOD   9:16:48

DCH 7 UIPE_IMSG CC_RELEASE_CONF   REF 0000010A CH 7 23 TOD   9:16:48
CAUSE: #16 - NORMAL CALL CLEARING
 
Upvote 0 Downvote
the route class = prt, Type: RBD, Rout: x, look for RCLS: INT/EXT

isn't DTI the same sort of thing as our DASS/DPNSS? if so look at LD75, you can use "enl mon X (loop number of the DDSL not the DDCS I think) decd

enl mon 8 decd

Remember if it doesn't work hit it harder

Scott UK
 
Upvote 0 Downvote
Route 4 (Long Distance): EXT
Route 6 (Local): EXT
Route 7 (Asterisk): EXT

Unfortunately looks like I can't get into 75:
Code: 
>ld 75

DTM007 0 IDA PACKAGE RESTRICTED

I was able to TRAD a call as it came into Long Distance:

Code: 
ACTIVE  TN 009 09
ORIG  009 09  TIE  RMBR  4 9
TERM  NONE
TDTN    0     SLOT    10   PTY SLOT  10
DIAL DN NONE
MAIN_PM  REOR
TALKSLOT  NONE
EES_DATA:
NONE
QUEU  DIAL
CALL ID 0 181

PDCA  1  PAD  0   0   PCML MU  MU

Code: 
ACTIVE  TN 009 09
ORIG  009 09  TIE  RMBR  4 9
TERM  NONE
DIAL DN NONE
MAIN_PM  HALFDISC
TALKSLOT  NONE
EES_DATA:
NONE
QUEU  NONE
CALL ID 0 181

PDCA  1  PAD  0   0   PCML MU  MU
 
Upvote 0 Downvote
Check these settings

LD 15 REQ: CHG
TYPE: NET_DATA
DITI = YES
EXTT = YES
FTOP = FTLY
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

HollTel
  • Locked
  • Question
TTY not working on a CS1K Rls. 7.0
Replies
2
Views
270
HollTel
HollTel
BSmith01
  • Locked
  • Question
Nortel PBX Password Change Issue
Replies
6
Views
264
BSmith01
BSmith01
JM2009
  • Question
SIP Tie trunks betwwen two CS1000
Replies
1
Views
97
Firebird Scrambler
Firebird Scrambler
John Tel
  • Locked
  • Question
CS1K Signaling Server partition full /dev/hda10 (Not the normal /var issue). Directory not working.
Replies
4
Views
382
John Tel
John Tel
LittleMaster
  • Locked
  • Question
Cs1k option 11c accounts.db 1
Replies
5
Views
168
LittleMaster
LittleMaster

Part and Inventory Search

Sponsor

Back
Top