Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
TMU
- Thread starter ozgur74
- Start date
Navdeep110
Technical User
Do CNHUI with relevant free board position , boardid is 102 with 32 timeslots
Enjoy
Enjoy
- Thread starter
- #4
All lims must have atleast one tmu card.
Or a set of the old cards TRU/TSU "MPU" optional
MPU is the conferecing unit (32 channels.)
The TMU is a multipurpose board that has theese
three functions buildt in.
You can not mix TMU and TRU/TSU/MPU in the same lim.
One TMU has
4 time-slots for DTMF-receivers
3 time-slots for dial-tone receivers.
The remaining time-slots can be distributed between conference and tone sender functions
ind Input to TMU Output to TMU
1 multi-party multi purpose
2 multi-party multi purpose
3 multi-party multi purpose
4 multi-party multi purpose
5 multi-party multi purpose
6 multi-party multi purpose
7 multi-party multi purpose
8 multi-party multi purpose
9 multi-party multi purpose
10 multi-party multi purpose
11 multi-party multi purpose
12 multi-party multi purpose/MOH1
13 multi-party multi purpose/MOH2
14 dial-tone tone-sender
15 dial-tone tone-sender
16 dial-tone/multi-party multi purpose
17 DTMF/multi-party DTMF/multi purpose
18 DTMF/multi-party DTMF/multi purpose
19 DTMF/multi-party DTMF/multi purpose
20 DTMF/multi-party DTMF/multi purpose
21 multi-party DTMF/multi purpose
22 multi-party DTMF/multi purpose
23 multi-party multi purpose
24 multi-party multi purpose
ind Input to TMU Output to TMU
25 multi-party multi purpose
26 multi-party multi purpose
27 multi-party multi purpose
28 multi-party multi purpose
29 multi-party multi purpose
30 multi-party multi purpose
31 multi-party multi purpose
Hope this helps
Or a set of the old cards TRU/TSU "MPU" optional
MPU is the conferecing unit (32 channels.)
The TMU is a multipurpose board that has theese
three functions buildt in.
You can not mix TMU and TRU/TSU/MPU in the same lim.
One TMU has
4 time-slots for DTMF-receivers
3 time-slots for dial-tone receivers.
The remaining time-slots can be distributed between conference and tone sender functions
ind Input to TMU Output to TMU
1 multi-party multi purpose
2 multi-party multi purpose
3 multi-party multi purpose
4 multi-party multi purpose
5 multi-party multi purpose
6 multi-party multi purpose
7 multi-party multi purpose
8 multi-party multi purpose
9 multi-party multi purpose
10 multi-party multi purpose
11 multi-party multi purpose
12 multi-party multi purpose/MOH1
13 multi-party multi purpose/MOH2
14 dial-tone tone-sender
15 dial-tone tone-sender
16 dial-tone/multi-party multi purpose
17 DTMF/multi-party DTMF/multi purpose
18 DTMF/multi-party DTMF/multi purpose
19 DTMF/multi-party DTMF/multi purpose
20 DTMF/multi-party DTMF/multi purpose
21 multi-party DTMF/multi purpose
22 multi-party DTMF/multi purpose
23 multi-party multi purpose
24 multi-party multi purpose
ind Input to TMU Output to TMU
25 multi-party multi purpose
26 multi-party multi purpose
27 multi-party multi purpose
28 multi-party multi purpose
29 multi-party multi purpose
30 multi-party multi purpose
31 multi-party multi purpose
Hope this helps
- Thread starter
- #6
Pushbutton telephone set:
23 Conference
You can establish speech connections with up to seven parties. Only the conference leader (i.e. the person initiating the conference call) can invoke participants.
Note The conference tone can by categorization be disabled.
23.1 To initiate a conference
A call to the first party is established.
Press the R-key (dial tone).
Dial the second party's extension number (inform about the conference).
Dial 3.
During the conference, conference tone will be heard.
23.2 To add a new party in a conference
Press the R-key (dial tone)
Dial the new party's extension number (inform about the conference).
Dial 3.
23.3 Internal consulting during a conference
As conference leader you can make an Inquiry call to one of the conference members.
Doing this you will get busy tone and to reach him/her you must use the Intrusion procedure.
Dial 1 (dial tone)
Dial the extension number (busy tone).
Dial 4.
You will now be connected to this conference member outside the conference for consultation. You can also release him/her from the conference.
Returning to the conference is possible as follows:
Return to the conference together with the consulted conference member - dial 3.
Refer back to the conference - you will return to the conference and the consulted conference member will be disconnected from the conference.
Clear the call and then refer back - the consulted conference member will be disconnected from the conference.
Make an Inquiry call - the consulted conference member will be disconnected from the conference.
23.4 To leave a conference
Replace the handset.
Note A tone burst is heard each time a participant enters or leaves the conference. The conversation is changed back to a normal two party connection when there is only two parties left. When the conference leader leaves the conference the conference will continue and the first one to park the conference will be the new conference leader.
DTS ( dialog family )
23.1 To initiate a conference
A call to the first party is established on Access 1-key.
Press the Inquiry-key or the Access 2-key.
Dial the second party's extension number (inform about the conference).
Press the Conference-key or dial 3.
During the conference, conference tone will be heard.
--------------------------------------------------------------------------------
23.2 To add a new party in a conference
Press the Inquiry-key or any idle Access-key (Access 1 or 2).
Dial the new party's extension number (inform about the conference).
Press the Conference-key or dial 3.
23.3 Internal consulting during a conference
As a conference leader you can make an Inquiry call to one of the conference members.
Doing this you will get busy tone and to reach him/her you must use the Intrusion procedure, see 18 Intrusion .
Press the Inquiry key (dial tone).
Dial the extension number (busy tone).
Press the Intrusion key or dial 4.
You will now be connected to this conference member outside the conference for consultation. You can also release him/her from the conference.
Returning to the conference is possible as follows:
Return to the conference together with the consulted conference member - dial 3.
Refer back to the conference - you will return to the conference and the consulted conference member will be disconnected from the conference.
Clear the call and then refer back - the consulted conference member will be disconnected from the conference.
Make an Inquiry call - the consulted conference member will be disconnected from the conference.
23.4 To leave a conference
Replace the handset.
Note A tone burst is heard each time a participant enters or leaves the conference. The conversation is changed back to a normal two party connection when there is only two parties left. When the conference leader leaves the conference the conference will continue and the first one to park the conference will be the new conference leader.
23 Conference
You can establish speech connections with up to seven parties. Only the conference leader (i.e. the person initiating the conference call) can invoke participants.
Note The conference tone can by categorization be disabled.
23.1 To initiate a conference
A call to the first party is established.
Press the R-key (dial tone).
Dial the second party's extension number (inform about the conference).
Dial 3.
During the conference, conference tone will be heard.
23.2 To add a new party in a conference
Press the R-key (dial tone)
Dial the new party's extension number (inform about the conference).
Dial 3.
23.3 Internal consulting during a conference
As conference leader you can make an Inquiry call to one of the conference members.
Doing this you will get busy tone and to reach him/her you must use the Intrusion procedure.
Dial 1 (dial tone)
Dial the extension number (busy tone).
Dial 4.
You will now be connected to this conference member outside the conference for consultation. You can also release him/her from the conference.
Returning to the conference is possible as follows:
Return to the conference together with the consulted conference member - dial 3.
Refer back to the conference - you will return to the conference and the consulted conference member will be disconnected from the conference.
Clear the call and then refer back - the consulted conference member will be disconnected from the conference.
Make an Inquiry call - the consulted conference member will be disconnected from the conference.
23.4 To leave a conference
Replace the handset.
Note A tone burst is heard each time a participant enters or leaves the conference. The conversation is changed back to a normal two party connection when there is only two parties left. When the conference leader leaves the conference the conference will continue and the first one to park the conference will be the new conference leader.
DTS ( dialog family )
23.1 To initiate a conference
A call to the first party is established on Access 1-key.
Press the Inquiry-key or the Access 2-key.
Dial the second party's extension number (inform about the conference).
Press the Conference-key or dial 3.
During the conference, conference tone will be heard.
--------------------------------------------------------------------------------
23.2 To add a new party in a conference
Press the Inquiry-key or any idle Access-key (Access 1 or 2).
Dial the new party's extension number (inform about the conference).
Press the Conference-key or dial 3.
23.3 Internal consulting during a conference
As a conference leader you can make an Inquiry call to one of the conference members.
Doing this you will get busy tone and to reach him/her you must use the Intrusion procedure, see 18 Intrusion .
Press the Inquiry key (dial tone).
Dial the extension number (busy tone).
Press the Intrusion key or dial 4.
You will now be connected to this conference member outside the conference for consultation. You can also release him/her from the conference.
Returning to the conference is possible as follows:
Return to the conference together with the consulted conference member - dial 3.
Refer back to the conference - you will return to the conference and the consulted conference member will be disconnected from the conference.
Clear the call and then refer back - the consulted conference member will be disconnected from the conference.
Make an Inquiry call - the consulted conference member will be disconnected from the conference.
23.4 To leave a conference
Replace the handset.
Note A tone burst is heard each time a participant enters or leaves the conference. The conversation is changed back to a normal two party connection when there is only two parties left. When the conference leader leaves the conference the conference will continue and the first one to park the conference will be the new conference leader.
Merhaba Ozgur:
This is what you have to do:
You have to allow Conference calls between different Categories by using TCMAS command.
When you have done this,dial B from ext A,hold it and than dial ext C and when answered press 3 (or conf key).Know you have a conference call.
Hope it helps
Hoscakalin
Jazaya
Experience it, there is no substitute.
RemoveThisJazayeri@kiasagroup.com
This is what you have to do:
You have to allow Conference calls between different Categories by using TCMAS command.
When you have done this,dial B from ext A,hold it and than dial ext C and when answered press 3 (or conf key).Know you have a conference call.
Hope it helps
Hoscakalin
Jazaya
Experience it, there is no substitute.
RemoveThisJazayeri@kiasagroup.com
- Thread starter
- #9
- Thread starter
- #10
- Thread starter
- #11
- Thread starter
- #13
- Thread starter
- #14
SPEECH WIRES CONTROL WIRES INDIVIDUAL
[tt]Wire pairs Make Break [/tt]
4A26 - 4A28 2A30 - 2A32 2A30 - 2C32 Ind. No. 1
4A18 - 4A20 2A22 - 2A24 2A22 - 2C24 Ind. No. 2
MUSIC-ON-HOLD1 is used in all application systems at parking. The usage of MUSIC-ON-HOLD2 and MUSIC-ON-HOLD3 is application system dependent.
The sound equipment is connected to the TMU board via the MDF
- Thread starter
- #16
You can test it with a acd group in bc11
and ragai with conann parameter
Don't you have any documentation
CONANN= D 1 D 2 D 3
D 1 D 2 D 3 = 0 Signifies that no continuous announcement is to be provided.
1-250 Announcement number, 1 - 250.
251 Tone Message, Music on hold input One.
252 Tone Message, Music on hold input Two.
253 Tone Message, Music on hold input Three.
254 Silence, No Announcement, No tone Message
The parameter CONANN is used to state the type of announcement to be connected when a call becomes queued or parked to both an ACD/PBX group and a PABX operator.
If the CONANN parameter is the only parameter entered together with the CORG or GRP, it is used to state the type of announcement to be connected when a call becomes queued or parked to both an ACD/PBX group and a PABX operator queue.If the parameter is entered together with the REPQUE parameter, the CONANN will be used to select which type of announcement will be provided between the repeated queue announcement message.
and ragai with conann parameter
Don't you have any documentation
CONANN= D 1 D 2 D 3
D 1 D 2 D 3 = 0 Signifies that no continuous announcement is to be provided.
1-250 Announcement number, 1 - 250.
251 Tone Message, Music on hold input One.
252 Tone Message, Music on hold input Two.
253 Tone Message, Music on hold input Three.
254 Silence, No Announcement, No tone Message
The parameter CONANN is used to state the type of announcement to be connected when a call becomes queued or parked to both an ACD/PBX group and a PABX operator.
If the CONANN parameter is the only parameter entered together with the CORG or GRP, it is used to state the type of announcement to be connected when a call becomes queued or parked to both an ACD/PBX group and a PABX operator queue.If the parameter is entered together with the REPQUE parameter, the CONANN will be used to select which type of announcement will be provided between the repeated queue announcement message.
- Thread starter
- #18
- Status
Similar threads
- Locked
- Question
