TMANI installation of OpenScape 4000 V7 system

[orinbw]

Dear Friends,

Please send me installation programs of above card. I have done the installation but CAN'T DIAL OUTGOING. But INCOMING calls are connecting and display the CLI.

When we dial OG number we can see the Trunk is seized ( TMANI flashing to indicate line busy condition as normal OG call ) after few seconds RELEASE the CO line. Then heat BUSY TONE.

Please send me complete programming ADD-TACSU, COP,COT, COS, RICHT,LDAT, LDPLN and LCOSV also. Is there any AMO to be done?

Thanks
Ravi

 

[hipath4k]

Dear Ravi

Share yours Ptime of Card.

Regards
Hello ,You can dicuss with me for Hipath 3k and Hipath 4K

 

[LAAZ]

Sample Configuration

Add Card
ADD-BCSU:MTYPE=PER,LTG=1,LTU=2,SLOT=79,PARTNO="Q2327-X100",FCTID=0,LWVAR="0",HWYBDL=A,ALARMNO=0;
Add trunk group
ADD-BUEND:TGRP=40,NAME="HKZ-TMANI ",NO=8,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDPMGRP=0,CHARCON=NEUTRAL;

add Cossu
ADD-COSSU:NEWCOS=8,INFO="TMANI";
CHANGE-COSSU:TYPE=COS,COS=8,AVCE=TA&TSUID&TNOTCR&TTT;
CHANGE-COSSU:TYPE=COS,COS=8,AFAX=NOCO&NOTIE;
CHANGE-COSSU:TYPE=COS,COS=8,ADTE=NOCO&NOTIE;
CHANGE-COSSU:TYPE=LCOSV,LCOSV=1,COPIN=0;
CHANGE-COSSU:TYPE=LCOSV,LCOSV=1,INFO="LCR ATTENDANT FOR VOICE";

add cop
ADD-COP:COPNO=40,PAR=DTMF&SFRM&RLSA&BR64&TDED&NO1A&DITW&TIM1&NSDL&IDP2&DTM1;
CHANGE-COP:COPNO=40,COPTYPE=COPADD,DEV=INDEP,INFO="TMANI-DTMF";

Add Cot
ADD-COT:COTNO=40,PAR=XFER&CHRT&NTON;
CHANGE-COT:COTNO=40,COTTYPE=COTADD,DEV=INDEP,INFO="TMANI-DTMF";

Add Dialing rule
ADD-LODR:ODR=99,CMD=ECHO,FIELD=2;
ADD-LODR:ODR=99,CMD=END;
ADD-LODR:ODR=99,INFO="NQ A2 OPEN";

Check P time
COPY-PTIME:INIBLOCK=119,TBLK=13;

Configure trunk
ADD-TACSUEN=1-2-79-0,COTNO=40,COPNO=40,DPLN=0,ITR=0,COS=8,LCOSV=1,LCOSD=1,TGRP=40,COFIDX=0,CCT="8102159AB001",DESTNO=0,ALARMNO=2,CARRIER=1,ZONE=EMPTY,LIN=0,CIDDGTS=NONE,CBMATTR=NONE,SRCGRP=0,CLASSMRK=EC&G711&G729AOPT,TCCID=" ",DITIDX=0,TRTBL=GDTR,RULEIDX=0,INS=Y,DEVTYPE=TC,DEV=TMANIMSG,MFCVAR=0,DGTPR=4808,SUPPRESS=0,DGTCNT=0,TESTNO=1,CIRCIDX=13,CDRINT=1,CCTINFO=0,DIALTYPE=DTMF-DTMF,DIALVAR=0-0,COEX=0;

Add trunk route
ADD-RICHT:MODE=LRTENEW,LRTE=40,LSVC=VCE,NAME="HKZ-TMANI ",TGRP=40,DNNO=1,REROUT=NO,DTMFTEXT="",ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CHARCON=NEUTRAL,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO;
Add-Linedata
ADD-LDAT:LROUTE=40,LSVC=VCE,LVAL=1,TGRP=40,ODR=99,LAUTH=1,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=4;

Addtrunk access code
ADD-WABE:CD=555,DAR=CO,CHECK=N;
Add dialing pattern
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=555-X,LROUTE=40,LAUTH=1,PINDP=N;

Hi
This is taken from Mnaual for configuration of TMANI in hipath 4000

 

[LAAZ]

P Ti,e for India for both SS and LL

Country
Input
impedan
ce
Balance
Impedan
ce
Atte
nuati
on
A-D
Atte
nuati
on
D-A
C
O
EX
P12 P14 P5 P6 Pƒn
11
P1
3India
600
600
-7
-0,5
0
0
37
12
65
6
0
SL
-9
2
12
LL