Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Ti/PRI Call ID 2

Status
Not open for further replies.
DaVinici

DaVinici

Vendor
Jul 23, 2001
98
US
With a PRI ckt...any special programming needed to get Call-Id...or does it automatically send the call id info
to the sets..my customer has a At&t T1 ckt used for DID's.
Right now no call id info is being sent...At&t says their
ckt should be doing so....any ideas..thanks. The switch is
Legend 7.010 w/ a 100d T1 card.
 
Sort by date Sort by votes
Well, is AT&T providing PRI or 2-way D-I-D?

With PRI you should get caller ID.

However, there is a "GLYTCH" in R3 of the Magix that clobbers it somehow.

 
Upvote 0 Downvote
No caller id available with that thru the T1.

Caller ID on T1 is only available with PRI on the Legend/Magix.
 
Upvote 0 Downvote
Chadoe, do you have a T-1 or a PRI?

Pepperz@charter.net
 
Upvote 0 Downvote
That's what was throwing me off, then, your first post mentioned a PRI circuit. If it is a regular T-1 circuit, then no caller ID.

Pepperz@charter.net
 
Upvote 0 Downvote
so with the PRI ckt...there is no extra programming for Call ID...it automatically starts.
 
Upvote 0 Downvote
Yep. There is a significantly different programming for the PRI itself, but in general, PRI = receive Caller ID.

Pepperz@charter.net
 
Upvote 0 Downvote
Now for the next set of q's.
If the customer I have wants to change from the 2way-DID T1 to a PRI...can I use the same 100d card and I did notice
a set of parameters to program for the PRI ckt. Will I have to remove the
translations of the T1 first. I have never installed a PRI
ckt...so any help is welcomed.
 
Upvote 0 Downvote
More or less, when you tell the T1 it iss a PRI the main T1 programming will go away.

 
Upvote 0 Downvote
anything special I need to know about installing a PRI ckt.
what to look for....possible problems...etc.
 
Upvote 0 Downvote
The only things that come to mind are this:

If you have any 016 Modules, DO NOT USE A 517M15 T1 pack.
 
Upvote 0 Downvote
are you refering to the ox16 mlx or the 0x16 t&r pack.
what release of ti card is the 517m15.
 
Upvote 0 Downvote
In MAINTENANCE, SYSTEM. INVENTIORY:

517E15 - Hardware 5B, Firmware 90

517M15 - Hardware 0A, Firmware 91
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

rcc1000
  • Locked
  • Question
No Caller ID
Replies
3
Views
138
Dexman
Dexman
CPM86
  • Locked
  • Question
Partner ACS DSL 1600 card an caller id. Is it no like the T1 module?
Replies
1
Views
133
Westi
Westi
Jim E
  • Locked
  • Question
Merlin Legend Call ID
Replies
1
Views
91
Dexman
Dexman
jsaad
  • Locked
  • Question
r7 caller id on display 1
Replies
10
Views
138
jsaad
jsaad
endel2005
  • Locked
  • Question
Avaya Partner ACS - R6 - Call Forwarding - Green Lights Flashing until each is pressed to clear
Replies
0
Views
111
endel2005
endel2005

Part and Inventory Search

Sponsor

Back
Top