The incall display not corectly

[lanpham_imported]

Hi everyone!
My system is the OS4KV8.
I have a ISDN trunk between the OS4KV8 and Toll pabx.
All the calls are successful, both incall and out call works perfectly, but caller ID for inbound EXTERNAL calls does not show number of the caller, instead just only shows * sign.
Please give me advise. Tks!
Brs!

 

[hipath4k]

share below:-

dis-sdat
dis-kndef

Regards
Hello ,You can dicuss with me for Hipath 3k and Hipath 4K

 

[lanpham_imported]

Dear hipath4k!
Please see the below:
DIS-SDAT:40200;
DIS-SDAT:40200;
H500: AMO SDAT STARTED

---------------------------- SUBSCRIBERDATA ----------------------------
STNO = 40200 COS1 = 1 DPLN = 14 SSTNO = NO
PEN : 1- 7- 2- 15 COS2 = 1 ITR = 0 TRACE = NO
DVCFIG : OPTIIP LCOSV1 = 3 COSX = 0 ALARMNO = 0
AMO : SBCSU LCOSV2 = 3 SPDI = 0 RCBKB = YES
LCOSD1 = 3 SPDC1 = RCBKNA = NO
KEYSYS : LCOSD2 = 3 SPDC2 =
------------------------------------------------------------------------
CDRACC =
SRCGRP = ( 1) TCLASS =
CLASSMRK = EC G711 G729AOPT
PUBNUM = TON = NPI =
NNO = 30 HOTIDX =
STNOOOS = MVHFAIP = NO
STNOAPE = AMOALTRT = NO
GWIPADR : CLUSTID =
SVCDOM =
PRECLEV =
BWLIDX =
CLASSSEC = SECURE
SECONLY =
STAONDNO =
------------------------------- ATTRIBUTES -----------------------------

------------------------------------------------------------------------

AMO-SDAT -111 ADMINISTRATION OF SUBSCRIBER ATTRIBUTES AND DATA
DISPLAY COMPLETED;
<DIS-KNDEF;
DIS-KNDEF;
H500: AMO KNDEF STARTED
VIRTUAL NODE TABLE
+-----------+--------+--------------+--------------+-----------+-----+----+----+
| VIRTUAL | TYPE | ISDN (E.164) | PRIVATE(PNP) | UNKNOWN |POPU-|CAC |DFLT|
| NODE | | CC | L2 | | LA- |PRE-| |
| NUMBER | | AC | L1 | |TION |FIX | |
| | | LC SK | L0 SK | NODECD SK | | | |
| | | PD | PD | | | | |
| | | UL | UL | VNRGRP | | | |
+===========+========+==============+==============+===========+=====+====+====+
| 1 |OWN | | | | 346| | Y |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | EXT | EXT | 0 | | | |
+ +========+==============+==============+===========+=====+====+====+
| | DPLN | ADPLN | |
+ +========+==============+==============+===========+=====+====+====+
+ | | |
+-----------+--------+--------------+--------------+-----------+-----+----+----+
| 30 |OWN | 84 | | | 2| | |
| | | 80 | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | EXT | EXT | 0 | | | |
+ +========+==============+==============+===========+=====+====+====+
| | DPLN | ADPLN | |
+ +========+==============+==============+===========+=====+====+====+
+ | | |
+-----------+--------+--------------+--------------+-----------+-----+----+----+
| 38 |OWN | | | | 0| | |
| | | 80 | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | EXT | EXT | 0 | | | |
+ +========+==============+==============+===========+=====+====+====+
| | DPLN | ADPLN | |
+ +========+==============+==============+===========+=====+====+====+
+ | | |
+-----------+--------+--------------+--------------+-----------+-----+----+----+
| 28 |OWN | | | | 0| | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | NAT | EXT | 0 | | | |
+ +========+==============+==============+===========+=====+====+====+
| | DPLN | ADPLN | |
+ +========+==============+==============+===========+=====+====+====+
+ | | |
+-----------+--------+--------------+--------------+-----------+-----+----+----+
H08: VNR IS NOT CONFIGURED

AMO-KNDEF-111 VIRTUAL NODES
DISPLAY COMPLETED;
Pls give me some ideas
Tks
Brs!

 

[hipath4k]

Try this

Cha-sdat
Stn:- 40200
pubnum:- 40200
ton:-unknown
npi-isdn

Regards
Hello ,You can dicuss with me for Hipath 3k and Hipath 4K

 

[Moriendi]

The problem is incoming calls?

First you should use RDS Tracer from the Assistant to make an ISDN trace of the incoming call. You should look at the incoming setup message to check if the calling number is delivered by the central office.

 

[lanpham_imported]

Dear all!
Many thanks for your help
I tried as Hipath4K help but it did not work
I am going to test as Moriendi next week.
Brs!

 

[lanpham_imported]

Dear all!
I made an ISDN trace of the incoming call and the result as below:

Direction

Station/PEN

BCH

Call Reference

Message Type

Time


Incoming 1-2-1-0 177 (H'B1) SETUP (H'5) 16:04:38:040

ok 2368 "(Incoming SETUP (H'5) on 1-2-1-0)

ProtocolDescriptor: Q.931 family (e.g. CorNet-N(Q), DSS1, ...) (H'8)

CallReference:

CallReferenceLength: 2

CallReferenceFlag: 0

CallReferenceValue: 177 (H'B1)

MessageType: SETUP (H'5)

InfoElem: Sending complete (H'A1)

InfoElem: Bearer capability (H'4)

HexData: 039090A3


Length: 3 (H'3)

CodingStandard: CCITT standardized coding (H'0)

InformationTransferCapability: 3.1 kHz audio (H'10)

TransferMode: Circuit-mode / call independent signalling (H'0)

InformationTransferRateAndMode: 64 kbit/s (H'10)

UserInformationLayer-1-Protocol: Recommendation G.711 A-law (H'3)

InfoElem: Channel identification (H'18)

HexData: 03A18381


Length: 3 (H'3)

InterfaceIdentifierPresent: Interface implicitly identified

InterfaceType: other than basic interface (e.g. primary rate)

Preferred/Exclusive: indicated channel is preferred

SignallingChannelIndicator: channel identified is not signalling channel (D-channel)

InfoChannelSelection: as indicated in following octets

CodingStandard: CCITT standard

Number/map: channel is indicated by number in following octet

ChannelType: B-channel units (64 kbit/s)

ChannelNumber: 1 (H'1)

InfoElem: Progress indicator (H'1E)

HexData: 028483


Length: 2 (H'2)

CodingStandard: CCITT standardized coding

Location: Public network serving the remote user

ProgressDescription: Origination address is non-ISDN

InfoElem: Called party number (H'70)

HexData: 06C13430323939


Length: 6 (H'6)

NumberingPlanIdentification: ISDN / Telephony numbering plan

TypeOfNumber: Subscriber number (H'4)

NumberDigits: "40299"


I only see the called number, don't show the calling number
Brs!