We are trying to setup a test lab for a future WAN configuration. We are having trouble getting complete/consisten connectivity through the setup in our test lab. Basically, we have what would be 2 remote sites sitting next to each other.
Equipment:
* 2 workstations (one on each end)
* 4 Cisco 1760 routers (2 on each end, one router with a 10BT Ethernet WIC Card, one with a T1 CSU/DSU WIC Card)
* 2 10/100 Switches
Baically, the setup we are trying to get to work in the lab is:
Workstation---Switch----10BT Router---T1 Router
Then from the T1 Router into a mirror of the above...so
W--S--10BT Router--T1 Router--T1Router--10BT Router--S--W
Now the connections of these are as follows:
The workstation connects into the switch via a straight through cable, the 10BT Ethernet port is connected into the switch via a straight through cable, the 10BT Ethernet router's 10/100 FastEthernet port is connected via cross-over cable to the 10/100 FastEthernet port of the T1 CSU/DSU Router. The two T1 CSU/DSU ports are connected via cross-over cable.
In the final setup, there will be a device which sits between the 10BT Router and the T1 Router, yet it simply acts as a passthrough and its only requirement is that it must have 1 subnetwork on its input, and a different subnetwork on its output...but we can simulate this using static routes without any problems.
When we started, we were unable to ping past our first router from the workstation. At this point we can get all the way up to the T1 CSU/DSU of the distant end. We can even get all the way up to The 10BT port of the distant end if we modify our IPs. As this will be replicated many times in the future, we would like to be able to configure all the boxes the same (we will have a little over 100 sites by the time we are done). So a unique address on each router would not be as easily managed as the same configuration for every box of the same type (ie all T1 CSU/DSU, all 10BT Ethernet, etc.) So we are trying to use a 10.0.0.0 addressing scheme. Our ability to get further in pinging has only occured after making every stop along the way its own subnetwork (ie 10.0.1.0, 10.0.2.0, etc.) and just keep incrementing along the way. Yet this does us no good in our final config. Also, one thing we found out was that OSPF helped to get it working better, but really not sure if we have it fully configured properly or not.
Any help would be appreciated. (PS. Sorry so long)
Equipment:
* 2 workstations (one on each end)
* 4 Cisco 1760 routers (2 on each end, one router with a 10BT Ethernet WIC Card, one with a T1 CSU/DSU WIC Card)
* 2 10/100 Switches
Baically, the setup we are trying to get to work in the lab is:
Workstation---Switch----10BT Router---T1 Router
Then from the T1 Router into a mirror of the above...so
W--S--10BT Router--T1 Router--T1Router--10BT Router--S--W
Now the connections of these are as follows:
The workstation connects into the switch via a straight through cable, the 10BT Ethernet port is connected into the switch via a straight through cable, the 10BT Ethernet router's 10/100 FastEthernet port is connected via cross-over cable to the 10/100 FastEthernet port of the T1 CSU/DSU Router. The two T1 CSU/DSU ports are connected via cross-over cable.
In the final setup, there will be a device which sits between the 10BT Router and the T1 Router, yet it simply acts as a passthrough and its only requirement is that it must have 1 subnetwork on its input, and a different subnetwork on its output...but we can simulate this using static routes without any problems.
When we started, we were unable to ping past our first router from the workstation. At this point we can get all the way up to the T1 CSU/DSU of the distant end. We can even get all the way up to The 10BT port of the distant end if we modify our IPs. As this will be replicated many times in the future, we would like to be able to configure all the boxes the same (we will have a little over 100 sites by the time we are done). So a unique address on each router would not be as easily managed as the same configuration for every box of the same type (ie all T1 CSU/DSU, all 10BT Ethernet, etc.) So we are trying to use a 10.0.0.0 addressing scheme. Our ability to get further in pinging has only occured after making every stop along the way its own subnetwork (ie 10.0.1.0, 10.0.2.0, etc.) and just keep incrementing along the way. Yet this does us no good in our final config. Also, one thing we found out was that OSPF helped to get it working better, but really not sure if we have it fully configured properly or not.
Any help would be appreciated. (PS. Sorry so long)