TAC dial over a tie line

[OpethBWP]

I have a P2P tie line setup between an Op11c and a dialer.

When I dial the ACOD for that route I am getting a busy signal.

I have checked the TARG (01) and TGAR (0) so obviously its not a problem there as that should work based on what I read\remember.

Here is the RDB for that route, anything I am obviosly missing

TYPE RDB
CUST 00
DMOD
ROUT 20
DES  DIALER_P2P
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
RCLS EXT
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD XXXX
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC  NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
     OGF 512
     EOD 13952
     DSI 34944
     NRD 10112
     DDL 70
     ODT 4096
     RGV 640
     GRD 896
     SFB 3
     TFD 0
SST  5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR  NO
MUS  NO
MANO NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0


PAGE 002

FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TTBL 0
OHTD NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

 

[bigindian65]

what is the NCOS of the sets versus the FRL of the RLI??

Mato' Was'aka

 

[telebub]

Did you stat the loop in Ld 60? Are all channels idle?

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

Really, the phones are TGAR 0 ? I ask because "Default" is TGAR 1 - which would mean you could not dial the ACCD - you would get a fast busy.

First, define "busy signal" as "slow/normal" or "fast/reorder"

If fast busy, trunks do not exist or are disabled or youi are restricted.

If slow/normal busy, trunks are all in use or lockout.


[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[GHTROUT]

NCOS does not apply to dialing ACOD's. NCOS only applies to calls that dial AC1 or AC2.



[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[GHTROUT]

Ooops, or CDP.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[bigindian65]

duh, yeah, thanks (again) didnt pay attention to what he was dialing there....

Mato' Was'aka

 

[OpethBWP]

Thanks for all the responses!

1. Trunk groups are idle (loops 4, 5 and 6)
2. This phone can dial another ACOD without issue so I am printing these 2 out to compare.
3. Its a fast busy and confirmed the phones are TGAR 0

Here is a print of the phone

DES  BOSS
TN   024 0 00 12
TYPE 3904
CDEN 8D
CUST 0
FDN  5256
TGAR 0
LDN  NO
NCOS 7
SGRP 0
RNPG 4
SCI  0
SSU
LNRS 16

 

[telebub]

Is this something that has been working and now has stopped for some reason or is this a new setup?

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

If these are new, and you are just turning them up, try toggling the Route 20 MANO prompt to YES

Although your symptoms don't perfectly match what MANO solves, I suppose since you are there and we are here, I should toss out that idea.



[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[OpethBWP]

Essentially it is a new setup.

Comparing the two trunk groups is not 100% similar in this case because the one they can dial is a TKTP DID ISDN(PRI) and the one they can not dial is a TKTP TIE

 

[GHTROUT]

If you change the phone CLS to UNR and it works, that is a clue that MANO will solve it for all other users.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[OpethBWP]

1. Changed CLS on the TN to UNR

2. Changed MANO to yes on the RDB

Still no luck..

here is a TRCK of the originating TN in LD 80 it shows it going to ROUTE 20 whjich is the right route for this trunk group.

 TN 024 0 00 12
KEY 2  SCR MARP ACTIVE  TN 024 0 00 12
ORIG  024 0 00 12  2  SCR MARP  0  5231  3904
TERM  006 24  TIE  RMBR  20 72
DIAL DN 8120
MAIN_PM  DIAL    AUX_PM  OUTPULSE
TALKSLOT  ORIG  6   TERM  10
EES_DATA:
NONE
QUEU  128
CALL ID 0 137


PDCA  1  PAD  0   6   PCML MU  MU

 

[GHTROUT]

There's no fast or slow busy on that call. The call seems to have completed...or at least will complete.

The busy sig may be coming from the other system?

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators