T1 PRI 100D issue 1

[jagrasmick]

Approx 2 years ago we moved from a plain T1 to PRI utilizing 100D board. I have been backing up the system and the other day I had to reboot the system and now the T1 won't work either in or outbound.

A tech brought in a new switch matched the settings and still won't work.

Qwest (local provider) brought in a T Bird and tested and verified circuit. Everything matched and worked good to the equipment.

I have restored the system with a number of backed up configurations but no luck. This is day 2 being down.

 

[merlinman]

Print the PRI & T1 Settings and post them.

Also, post how QWEST has it set up.

AND, where 'bouts are you?

Mayhaps some one local needs to assist.

 

[jagrasmick]

DS1 INFORMATION



DS1 SLOT ATTRIBUTES

Slot Type Format Supp Signal LineComp
4 PRI ESF B8ZS DMI-MOS 1



----------------------------------- ANNOTATION -----------------------------------
PRI INFORMATION



Slot 4 Switch: 5ESS

System: By extension Base number: 7197852100

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 4 CallbyCall By Dial Plan

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 3 3 2 2 1 0 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
PRI INFORMATION


Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: VOICE BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service Any service Any service Any service
Expected Digits: 4 0 0 0
Pattern to Match: 0 1 2 3
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 4 5 6 7
NtwkServ: Any service Any service Any service Any service
Expected Digits: 0 0 0 0
Pattern to Match: 4 5 6 7
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ: Any service Any service Any service Any service
Expected Digits: 0 0 0 0
Pattern to Match: 8 9 10 11
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ: Any service Any service Any service Any service
Expected Digits: 0 0 0 0
Pattern to Match: 12 13 14 15
Digits to Delete: 0 0 0 0
Digits to Add:



----------------------------------- ANNOTATION -------------
----------------------


Qwest has claims to be B8ZS, ESF, Timming comes from Qwest

 

[jagrasmick]

Almost forgot to add that I am located in Colorado Springs

 

[SYQUEST]

Any alarms in the ERROR LOG?

Do you get recordings or fast busies on incoming?

Did Qwest unbusy the B and D channels?

Double check that trunk 832 IS NOT in any pool/group or assigned to anything else. This is your D channel.

I did not see anything jump off the page from your printout. When you attempt to place an outgoing call does the Yellow LED on the 100D lite at any time, even for a brief moment?

....JIM....

 

[jagrasmick]

I am receiving errors 7001 on all ports of the T1 card.

When dialing from outside to a DID number the recording is all circuits are busy. From inside to outside dialing it is a fast busy.

I'll have qwest check the B and D channels.

I just double checked 832 is not part of the pool.

On either a out and inbound the yellow LED never goes on.

 

[merlinman]

Looking at the Print at my location in Aurora, I do not see any jump off the page issues either.

What does Qwest tell you they are seeing from the switch.

Also, Print & Post the ERROR LOG.

 

[jagrasmick]

Finally found the problem. The CO programming was set to National and not custom. The person that found this difference was Jason (720)480-0305 below are his notes on setup.

PRI SETUP ON LEGEND/MAGIX

Set Frame Format to Extended Super Frame-Lines/trunks?LS/GS/DS1?’Enter Slot’+ Enter?Frame Format?Extended Super Frame?Enter

Set Suppresion- Lines/trunks?LS/GS/DS1?’Enter Slot’+ Enter?Suppression?B8ZS?Enter

Change Type to PRI- Lines/trunks?LS/GS/DS1?’Enter Slot’+ Enter?Type?PRI?Enter (System will Reset/Reboot)

Set Switch Type- Lines/trunks? PRI?Switch Type?( This is the switch you are connecting to; If it is a DMS-100 to Qwest put that here)?Enter

Program B-Channel Group-B-Channel Group?B-Channel?(1-80 use; 1 first) + Enter?slot/B-channel starting from the last channel( ex. 0323enter,0322enter,0321enter,…..etc) for slot 3 channel 23,slot 3 channel 22…etc.

Program Lines-Bchannel?Lines?Group number( see step 5 )+ Enter?Enter the lines ( up to 23 only per group)

Set Network Service-B-channel Group?Network Service?Misc?CallbyCall?Enter

Set Incoming Routing- B-channel Group?Incoming Rtg?Dial Plan?Enter

Program Dial Plan Routing- PRI? Dial Plan Routing?Service?0(zero)?Misc?Any?Enter

Program Outgoing Table- ?Outgoing Table?CBC Svc?Pattern?Enter 00?Enter (When Prompted for Pattern enter 0?Next?1?Next?2?Next ………8?Next?9?Enter

Set No Service-Outgoing Table?CBC?Network Service?0?Misc?No Service

Notes
Can not change switch type to 4E, 5E, Legend netwrk etc when Data channels are programmed on the DCD board-Channels must be voice or unequipped.
Protocol-Custom Only National Will Not Work
CO’s That are compatible-4ESS, 5ESS General 16, 5ESS Serving FTS, DMS-100 BC3 36 2000 Network, DMS-250 Serving MCI, DEX600E
CSU/DSU-ESF / B8ZS both NET and DTE Channels DTE-Assign N1-N24=D1-D24; D1-D23=RBS-RBS; D24=Data
ANY TIE CONNECTIONS-Setting Switch Type to Legend??? Defaults Network service and Dial Plan which cannot be changed

 

[merlinman]

Where does this Jason work?